manualshive.com logo in svg

Olympus TRPP 5810, User Manual

Share
Download
Olympus TRPP 5810 User Manual Download Page 29

DMTA-20070-01EN, Rev. A, October 2014

Maintenance

 

23

3. Maintenance

The maintenance requirements for the TRPP 5810 remote pulser/preamplifier are 
minimal.

3.1

Preventive Maintenance

Because the TRPP 5810 remote pulser/preamplifier has no moving parts, it does not 
require preventive maintenance. Only a regular inspection of the product is 
recommended to ensure that the TRPP 5810 unit functions correctly.

3.2

Unit Cleaning

The TRPP 5810 external surfaces can be cleaned when needed. This section provides 
the procedure for the appropriate cleaning of the product.

To clean the unit

1.

Ensure the unit is turned off by removing the source of power.

2.

Disconnect all cables.

3.

To bring the instrument back to its original finish, clean the housing with a soft 
cloth.

4.

To remove persistent stains, use a damp cloth with a soft, soapy solution. Do not 
use abrasive products or powerful solvents that could damage the finish.

5.

Wait until the instrument dries completely before connecting the cables.

Summary of Contents for TRPP 5810













































Reviews:

No comments

Brands by name

Popular brands

Load more brands