background image

30 

access code, a special access code, derived from the BD-ADDRESS 
of the paged device will be, will be sent by the master of this 
connection. Due to the fact that both units have been connected 
before (in the inquiry procedure) the paging unit has timing and 
frequency information about the page scan of the paged unit. For this 
reason the time to establish the connection is reduced. 
 

11. Spread Rate I Data Rate of the Direct Sequence Signal 

 

The spread rate / data rate in inquiry and paging mode can be 
defined via the access code. The access code is the only criterion for 
the system to check if there is a valid transmission or not. If you 
regard the presence of a valid access code as one bit of information, 
and compare it with the length of the access code of 68 bits, the 
spread rate / data rate will be 68/1. 

 

12. Spurious Emission in Hybrid Mode 

 

The dwell in hybrid mode is shorter than in data mode. For this 
reason the spurious emissions average level in data mode is worst 
case. The spurious emissions peak level is the same for both modes. 
 
 

Battery Caution 

 

Caution:

 Danger of explosion if battery is 

incorrectly replaced. Replace only with the same 
type recommended by the manufacturer. Discard 
used batteries according to the manufacturer’s 
instruction. 
 
 
 

Service Information 

 

Refer to www.olympus-ost.com to get more 
information 
 
 

Summary of Contents for R1000 Series



































Reviews: