background image

E-2

1. Keep this product out of the reach of babies, infants, and children.

There is the possibility of occurrence of the following types of
accidents.

Injury by dropping onto the body from a height.

Injury from parts of the body getting caught in parts which open
and close.

Swallowing of small parts. Please consult a physician immediately
if any parts have been swallowed.

Triggering of the flash in front of the eyes may cause permanent
vision impairment etc.

2. Do not store with a battery in the digital camera housed in this

product. Storage with a battery inserted may lead to leakage of the
battery liquid and fire.

3. If leakage of water should occur with a camera installed in this

product, quickly remove the battery from the camera. There is the
possibility of ignition and explosion from generation of hydrogen gas.

4. This product is made of resin. There is the possibility that injuries

may be caused when it becomes broken because of strong impact
with a rock or other hard objects. Please handle with sufficient care.

5. The silica gel and the grease for silicone O-rings for this product

are not edible.

1. Do not disassemble or modify this product. This may cause water

leakage or trouble. In case of disassembly or modification by
persons other than those appointed by our company, the guarantee
shall not apply.

2. Do not place this product at locations with abnormally high or

abnormally low temperatures or at locations with extreme
temperature changes. The product may deteriorate.

3. Opening and closing at locations with much sand, dust, or dirt may

impair the waterproof characteristic and cause water leakage. This
should be avoided.

4. This product has been designed and manufactured for use at a

water depth within 40 m. Please note that diving to a depth in
excess of 40 m may cause permanent deformation or damage to
the Case and the camera inside the Case or may lead to water
leakage.

WARNING

CAUTION

PT̲019̲en.qxd    2003.9.19  2:13  PM    ページ E-2 (1,1)

Summary of Contents for PT-019







































Reviews: