Olympus PT-018 Instruction Manual Download Page 12 | Manualshive

Page: 12 / 38

background image

E-11

Install the strap.

Install the strap on the Case body.

：Please install the strap correctly as shown above. Our company

shall bear no responsibility for damage etc. caused by dropping
the Case because of incorrect installation of the strap.

CAUTION

：・Do not exert excessive force onto the lens window or the lens ring.

・Take care not to put your fingers etc. over the lens window

and the flash diffuser.

CAUTION

Master the basic operation.

Please master the basic operation of the Case before taking pictures.

Holding the Case

Hold the Case securely with both hands, keep your elbows close to your body,
and hold the Case so that you can confirm the picture on the LCD monitor of
the digital camera through the LCD monitor window of the Case.

Note

：・ Use the LCD monitor to confirm your picture. The viewfinder

cannot be used.

Installation explanation

Hand strap

Hand strap ring

Finished installation

Good example

Bad example

«
...
10
11
12
13
14
...
»

Summary of Contents for PT-018







































Reviews:

No comments

Related manuals for PT-018

Super G3 FAX Board-T1

Brand: Canon Pages: 16

iP4000 - PIXMA Photo Printer

Brand: Canon Pages: 3

Brand: Canon Pages: 21

Brand: Canon Pages: 6

7215 - LV XGA LCD Projector

Brand: Canon Pages: 8

Brand: Manfrotto Pages: 4

Brand: TaylorMade Pages: 5

Brand: Accessory Power Pages: 36

Brand: Young Living Pages: 41

Brand: ICON Pages: 8

Brand: Warmup Pages: 4

Brand: Yeti Pages: 19

Brand: veba Pages: 11

Brand: Microlife Pages: 121

Brand: Ultra-tow Pages: 14

Brand: KERN Pages: 4

Brand: Menabo Pages: 8

Brand: Camtree Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands