manualshive.com logo in svg

Olympus OLYMPUS BF TYPE 160, Operation Manual, Page: 45 / 70

Share
Download
Olympus OLYMPUS BF TYPE 160 Operation Manual Download Page 45

Chapter 4  Operation

41

BF TYPE 160 Series OPERATION MANUAL



Suction

Avoid aspirating solid matter or thick fluids; channel or valve 
clogging can occur. If the suction valve clogs and suction 
cannot be stopped, disconnect the suction tube from the 
suction connector on the suction valve. Turn the suction 
pump OFF.

During the procedure, take notice that the suction bottle does 
not fill completely. Aspirating fluids into a full bottle may 
cause the suction pump to malfunction.

Press the suction valve to aspirate excess fluid or other debris obscuring the 
endoscopic image (see Figure 4.3).

Figure 4.3

Observation of the endoscopic image

Refer to the light source’s instruction manual for instructions on how to adjust the 
brightness.

• For the BF-XP160F, the brightness setting on the video 

system center is too high. Set the iris mode selection switch 
on the video system center to peak iris mode. However, 
when the image turns dark by using endo-therapy 
accessories, set the iris mode selection switch to the average 
iris mode.

• For adjusting the white balance of the BF-XP160F, set the iris 

mode selection switch on the video system center to peak iris 
mode. Otherwise, it may not be possible to correctly adjust 
the white balance.

Suction valve

Summary of Contents for OLYMPUS BF TYPE 160







































































Reviews:

No comments