Olympus CelonLab ENT Instruction Download Page 3

 

Safety Check Instruction

 

 

 

 

 

 

 

©  Celon AG 

Page 3 / 9 

 

Issue date: 01.09.2008 

SCI.991007-1.4 

Safety Check 

Instruction.doc 

No. 

Procedure 

020 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

       

 

 

030 

Unit and accessories are externally undamaged: 
- Enclosure and front panel have no serious destructions 

040 

Lift up the unit and shake it gentle. No clatter noise should be audible. 

 

Documentation

 

050 

Docu

ment the test results in “SCR.991007. 

 

Sample of symbol:

  Connection for equipotential bonding 

 

Visible on the back of the unit (see fig. 1) 

Samples of label for power fuses: 

Visible on the back of the unit (see fig. 1) 

 

Sample of symbol: 

“Non-ionizing radiation” 

 

Visible on the back of the unit (see fig. 1) 

Sample of label for volume switch: 

Visible on the back of the unit (see fig. 1) 

Sample of label:

 

Product name 

 

Visible on the front panel (see fig. 2) 

 SPEAKER VOLUME 

 

HIGH 

 

LOW 

Sample of symbol: 

“Waste electrical and electronic equipment” 
Visible on the back of the unit, 

only applicable for 

units

 

within the European Union and sold after 

August 13th, 2005.

 (see fig. 1) 

 

Summary of Contents for CelonLab ENT










Reviews: