background image

9215

0

3

2

00_

0

9_01

0

Page

 

5

 

from

 5

Sound adjustment jumpers ( dB) 
The factory seting for the jumpers

 

is in the 

(

OFF) position

NOTE!!! After finishing the 
installation, place the SEAL 
sticker as shown in the picture.

WARRANTY

Olympia Electronics guarantees the quality, condition and operation of the goods. The period of 
warranty is specified in the official catalogue of Olympia Electronics and also in the technical leaflet, 
which accompanies each product. This warranty ceases to exist if the buyer does not follow the 
technical instructions included in official documents given by Olympia Electronics or if the buyer 
modifies the goods provided or has any repairs or re-setting done by a third party, unless Olympia 
Electronics has fully agreed to them in writing. 

Products that have been damaged can be returned to 

the premises of our company for repair or replacement, as long as the warranty period is valid.

Olympia Electronics reserves the right to repair or to replace the returned goods and to or not charge 
the buyer depending on the reason of defection. Olympia Electronics reserves the right to charge or 
not the buyer the transportation cost.

HEAD OFFICE

72

nd

 

km

O

.

N

.

R

Thessaloniki-Katerini

P

.

C

. 60

300

 

P.O. Box 06 Eginio Pierias

 

Greece

www.olympia-electronics.gr
[email protected]

Slow rate of 

buzzer sound

Fast rate of 

buzzer sound

1

ON

2 3 4

5 6 7 8

1

ON

2 3 4

5 6 7 8

Operation 

Mode

Dipswitch

setting

Summary of Contents for ΒSR-5032






Reviews: