background image

Technical Specifications

BS-634

4 zone fire

detection panel

BS-636

6 zone fire

detection panel

Mains power supply

220-240VAC  50/60Hz

48VA

One 12V 

 7Ah maximum

Lead acid sealed 

Stabilized power supply  13.8V / max. 400mA

36 hours (without using the outputs  24V_M and 24V_P)

Two  24V circuits that are monitored for open and short circuit conditions 

(maximum current 300mA each). Each output is protected  

with a self-reseting electronic fuse.

 26VDC ( ±3VDC)  permanent output  

The output is protected with a self-reseting electronic fuse.

with maximum current output  0.3 A

ABS - polycarbonate

Consumption

Battery type

Charging circuit

Autonomous duration

Zone circuits

Alarm circuits

Output   24P

Construction material

4 circuits monitored for

short and open circuit

conditions (maximum current 35mA)

6 circuits monitored for

short and open circuit

conditions (maximum current 35mA)

 26VDC ( ±3VDC)  reset interrupted output  with maximum current output  0.3 A

The output is protected with a self-reseting electronic fuse.

Output  24M

 One Aux relay and 

each. Under no circumstances should voltages or currents outside limits

 be connected.  All relays output must be protected  with a fuse of the same rating.

6 relays contacts are rated at  30VDC  and 5A maximum 

Outputs AUX, Zone Relays

325 x 240 x 85 mm

2040gr (4030gr with battery) 

ΕΝ 54-2, ΕΝ 54-4

2 years

Dimensions

Weight

Produced in accordance to

Guarantee

Open collector output signal  as specified in 8.8 of EN 54.2 (max. 30VDC/6mA)

Output  F_OUT

Up to  95% relative humidity

Humidity

o

0 to 50  C

Operation temperature

The total output current ( zones circuits, siren circuit, outputs 24P, 24M) 

must not exceed 700mA.

Total load

IP 30

Cables for fire rated cables systems such a FIP200,MICC, PYROFIL

The panel has only one serviceable fuse to protect incoming mains supply. 

This fuse is 

  must be replaced with a fuse 

of the same type and rating

T250mAL250V

IP

Cables

Fuse ratings

4 circuits monitored for

short and open circuit

conditions (maximum current 35mA)

6 circuits monitored for

short and open circuit

conditions (maximum current 35mA)

25VA

Page 9 from 9

921636000_09_023

Summary of Contents for BS-634










Reviews: