Page 2 from 3
Luminary Installation Procedure
923753002_09_002
WARRANTY
Olympia Electronics guarantees the quality, condition and operation of the goods. The period of warranty
is specified in the official catalogue of Olympia Electronics and also in the technical leaflet, which
accompanies each product. This warranty ceases to exist if the buyer does not follow the technical
instructions included in official documents given by Olympia Electronics or if the buyer modifies the goods
provided or has any repairs or re-setting done by a third party, unless Olympia Electronics has fully
agreed to them in writing. Products that have been damaged can be returned to the premises of our
company for repair or replacement, as long as the warranty period is valid.
Olympia Electronics reserves the right to repair or to replace the returned goods and to or not charge the
buyer depending on the reason of defection. Olympia Electronics reserves the right to charge or not the
buyer the transportation cost.
HEAD OFFICE
72
nd
km. O.N.R. Thessaloniki-Katerini
P.C. 60300 P.O. Box 06 Εginio Pierias Greece
www.olympia-electronics.gr
[email protected]
1
Place a flat blade screwdriver to the plastic hook and pull up gently to release the diffusor.
2
Remove the reflector.
3
Remove the led strip.
4
Use the included mounting parts to mount the base plastic.
5
Always use round mains cable, with a suitable diameter to fit tightly into the gasket.
ATTENTION!! The cable must not be deformed in any way (This requirement is
important to ensure the ΙΡ rating).
Always refer to GR-8600 manual regarding to the
cable’s cross section’s selection. Install
the included gasket into the cable entry hole
(verify
that is not deformed)
. Make a hole in the center by using a small screwdriver.
P
ass the
communication cables through the hole and connect them as shown on the picture (minding
the correct polarity). When there are other luminaries to be connected to the line we
recommend to open a second hole to pass the second pair of communication cables.
6
If the luminary you installed is the last one, connect the cable to one of the two inputs, as
shown on the picture (minding the correct polarity).
7
Address the device though the dipswitch according to the table on page 3.
8
Refit the led strip minding the connection with the P.C.B.
Warning!!
The holes of the led strip must be fit in the projections of the base.
9
Refit the reflector (mind the correct orientation) and tighten the screws.
10
Refit the diffusor (mind the correct orientation) and power on the device. (see GR-8600
manual).
Page 3 from 3
Addressing Table
Address
Dipswitch
setting
Address
Address
Address
Dipswitch
setting
Dipswitch
setting
Dipswitch
setting
5
6
7
8
9
10
1
1
1
1
1
1
ON
ON
ON
ON
ON
ON
2
2
2
2
2
2
3
3
3
3
3
3
4
4
4
4
4
4
5
5
5
5
5
5
6
6
6
6
6
6
11
12
13
14
15
16
17
18
19
20
1
1
1
1
1
1
1
1
1
1
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
3
3
3
4
4
4
4
4
4
4
4
4
4
5
5
5
5
5
5
5
5
5
5
6
6
6
6
6
6
6
6
6
6
21
22
23
24
25
26
27
28
29
30
1
1
1
1
1
1
1
1
1
1
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
3
3
3
4
4
4
4
4
4
4
4
4
4
5
5
5
5
5
5
5
5
5
5
6
6
6
6
6
6
6
6
6
6
1
ON
2 3 4 5 6
1
ON
2 3 4 5 6
1
ON
2 3 4 5 6
2
3
4
1
ON
2 3 4 5 6
1
31
32
1
ON
2 3 4 5 6
1
ON
2 3 4 5 6
923753002_09_002
6
5
-L
+L
-L
+L
-L
+L
1
4
9
8
