Olymberyl HF217-SE Baby Gabriel Instruction Manual Download Page 12 | Manualshive

Page: 12 / 44

background image

INSTALLATION

REGULATIONS

You must ensure that your stove is
installed by a recognised competent
person who is appropriately qualiﬁed
in the installation of stoves and that
the installation complies with all local,
national and European building
regulations.

In the UK we strongly recommend using
a Hetas registered installer (

www.hetas.

co.uk

) and in Ireland a registered

installer from INFO – the Irish
Nationwide Fireplace Organisation
(

www.ﬁreplace.ie

). Your authorised

Hi-Flame dealer will also be able
to help and advise you.
For further information on local
Building Regulations please consult:

England & Wales

Building Regulations Document J
(revised October 2010) – Combustion
Appliances and Fuel Storage Systems

www.planningportal.gov.uk

Scotland

Building Standards (2001) Domestic

www.sbsa.gov.uk

Northern Ireland

The Building Regulations (Northern
Ireland) 2000 / Amendment 2006 /
Amendment No 2 2006

www.buildingcontrol-ni.com

Isle of Man

Building Regulations (2007) –
Isle of Man

www.gov.im

12

Republic of Ireland

Approved Document J – Heat Producing
Appliances (Revised September 2014)

www.environ.ie

Other Information Points

For additional useful information and
links to the government websites
above, including informative down-
loads, visit The Solid Fuel Technology
Institute website

www.soliftec.com

.

The Solid Fuel Association website is
also a very good source of practical
information and downloads

www.solidfuel.co.uk

.

The British Flue and Chimney
Manufacturers Association website,
www.

bfcma.co.uk

produces an authori-

tative and informative download guide
to solid fuel ﬂues and chimneys.

Buildings Insurance

It is a requirement by some building
insurance companies to inform them of
the installation of a new ﬁxed heating
appliance and a relevant certiﬁcate of
compliance produced.

Health & Safety

During the installation of this stove and
any related building works you must
comply with any current Health
& Safety at Work regulations.

«
...
10
11
12
13
14
...
»

Summary of Contents for HF217-SE Baby Gabriel













































Reviews:

No comments

Related manuals for HF217-SE Baby Gabriel

Brand: Barmat Castings Pages: 10

Brand: Drolet Pages: 38

Brand: Wagener Pages: 9

Brand: Comfort Glow Pages: 13

Brand: Clarke Pages: 24

Brand: Clarke Pages: 28

Brand: Cadel Pages: 40

Brand: Univa Pages: 10

Hearth Focus 6039HF

Brand: United States Stove Pages: 24

Brand: United States Stove Pages: 40

Brand: Zanussi Pages: 2

Brand: Zanussi Pages: 16

Brand: Coleman Pages: 2

Brand: Coleman Pages: 16

Brand: Coleman Pages: 32

Brand: HAAS + SOHN Pages: 15

Brand: HAAS + SOHN Pages: 28

Thermofan 631 T

Brand: Defy Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands