background image

Outdoor Living Today                 www.outdoorlivingtoday.com            [email protected]

Page 1

8x4 GardenSaver 

Sliding Door - Plywood Roof - FJ Siding

 

Assembly Manual

Revision #1.4 

January 14, 2022 

Thank you for purchasing 
a 8x4 GardenSaver Shed 
with Sliding Door. Please 
take the time to identify all 
the parts prior to assembly.

Please be aware that it is the 
customers’ sole responsibility 
to acquire the necessary 
building permits and or obtain 
approval from their local 
county, municipality or HOA 
prior to purchasing. Generally, 
shed structures under 100 
square feet do not require 
permits in most jurisdictions 
in the United States and 
Canada.

In the event of a missing or broken piece, call the Outdoor Living Today Customer Support Line @ 1-888-658-1658 with-
in 30 days of the delivery of your purchase. It is our commitment to you to courier replacement parts, free of charge, 
within 10 business days of this notification. Replacement parts will not be provided free of charge after the 30 day 
grace period.  
 
All structures purchased from Outdoor Living Today are covered for a period of one year for defects in manufacturing 
and workmanship. Costs incurred for customer installations are not included. 
 
Failure to use supplied parts included in this kit could result in poor product performance and may void your warranty. 
Please contact Outdoor Living Today’s Customer Toll Free Line if you plan to deviate from our written instructions.

 

- Snow load ratings vary by geographical location. If heavy or wet snowfall occurs, it  
   is advisable to sweep snow off roof frequently. 
- If the product is elevated, any structural and building code requirements are solely 
   the customer's responsibility, and should be abided by.  
- In areas with high or gusty wind conditions, it is advisable to install the structure 
   securely to the ground. 
- Have a regular maintenance plan to ensure screws, doors, windows and parts are 
   tightly affixed.  

 
Customer agrees to hold Outdoor Living Today and any Authorized 
Dealers free of any liability for improper installation, maintenance and 
repair.

Stock Code:

 

GS84-SLIDER-PLY-FJ

Roof Area: 37.5 sqft

Summary of Contents for GS84-SLIDER-PLY-FJ




































Reviews: