background image

64.

 Place and align rear and side facia for best possible fit with rear capping side facia.  Attach facia 

to rafter ends with 6 - 1 1/2” finishing nails per piece.  Complete both rear facia pieces. 

Rafter/Facia Nailing Plate

Side Angle  
Cut Facia

63.

 Do a dry run first before securing. Position Front Facia up underneath roof panel and against 

rafter ends. Have your helper hold in position. Place angle cut Side Facia underneath roof panel 
against Rafter/Facia Nailing Plate.  Align so Front Facia caps Side Facia and then attach the front 
with 6 - 1 1/2” finishing nails.  Attach side with 5 - 1 1/2” nails securing them into the nailing plate 
(closer to the top of the side facia board).  Attach next piece of Front Facia.  

Note:

  With Front Facia 

correctly aligned at corners, a small gap may occur at center seam. This will be covered by Facia 
Detail Plate in 

Step 65.

Small gap 
may occur.

62.

 Locate and identify all Facia pieces: 

Front & Rear Facia (4) 

(1/2” x 4” x 50 1/2”).    

Side Angle Cut Facia (2) 

(1/2” x 4” x 54 1/8”). In front corner

align side and front Facia together

Front facia will cap side facia

.  

 

Front 
Facia

Front caps 
side facia.

  Toll Free 1-888-658-1658              www.outdoorlivingtoday.com        [email protected]

Page 29

Summary of Contents for GardenSaver GS84D-Plywood


































Reviews: