OLT CLA128-SLIDER-METAL-ES Assembly Manual Download

Page: 37 / 44

Corner Trim

Wide Corner
Trim

Toll Free 1-888-658-1658 www.outdoorlivingtoday.com [email protected]

Page 37

60.

To trim out corners, start with a

Corner Trim

align tight underneath Soffit and Rafter. Align

Wide

Corner Trim

with bottom of Corner Trim. Corner Trim

will cap the Wide Corner Trim. Do a dry run in each cor-
ner before attaching to confirm positioning. Use

8 - 1 1/2” Finishing Nails

per piece to secure.

Complete other front corner the same.

Parts (Steps 60 - 61)

Corner Trim

(1/2” x 3 1/2” x 79”)

x 4

Wide Corner Trim

(1/2” x 5 1/2” x 82”)

x 4

Hardware (Steps 60 - 61)

- 1 1/2” Finishing Nails

x 64 total

Align bottoms of both corner
trim pieces flush.

Fit Corner Trim tight
underneath Soffit.

61.

Trim out rear corners with remaining

pieces of

Corner Trim

and

Wide Corner Trim

Align and attach with

8 - 1 1/2” Finishing Nails

per piece as per

Step 60

Summary of Contents for CLA128-SLIDER-METAL-ES













































Search results

Summary of Contents for CLA128-SLIDER-METAL-ES

Reviews:

Related manuals for CLA128-SLIDER-METAL-ES

Brands by name

Popular brands

OLT CLA128-SLIDER-METAL-ES, Assembly Manual

Search results

Summary of Contents for CLA128-SLIDER-METAL-ES

Reviews:

Related manuals for CLA128-SLIDER-METAL-ES

Brands by name

Popular brands