OLT CB128-SLIDER-PLY-AK Assembly Manual Download

Page: 34 / 39

54.

Trim out rear corners with remaining

pieces of

Corner Trim

and

Wide Corner Trim

Align and attach with

8 - 1 1/2” Finishing Nails

per piece as per

Step 53

Align bottoms of both corner
trim pieces flush.

Fit Corner Trim tight
underneath Soffit.

53.

To trim out corners, start with a

Corner Trim

align tight underneath Soffit and Rafter. Align

Wide

Corner Trim

with bottom of Corner Trim. Corner Trim

will cap the Wide Corner Trim. Do a dry run in each cor-
ner before attaching to confirm positioning. Use

8 - 1

1/2” Finishing Nails

per piece to secure. Complete

other front corner the same.

Parts (Steps 53 - 54)

Corner Trim

(1/2” x 3 1/2” x 79”)

x 4

Wide Corner Trim

(1/2” x 5 1/2” x 82”)

x 4

Hardware (Steps 53 - 54)

- 1 1/2” Finishing Nails

x 64 total

Toll Free 1-888-658-1658 www.outdoorlivingtoday.com [email protected]

Page 34

Corner Trim

Wide Corner
Trim

Summary of Contents for CB128-SLIDER-PLY-AK








































Search results

Summary of Contents for CB128-SLIDER-PLY-AK

Reviews:

Related manuals for CB128-SLIDER-PLY-AK

Brands by name

Popular brands

OLT CB128-SLIDER-PLY-AK, Assembly Manual

Search results

Summary of Contents for CB128-SLIDER-PLY-AK

Reviews:

Related manuals for CB128-SLIDER-PLY-AK

Brands by name

Popular brands