background image

PAGE 1

WARNING:

ALL INSTALLATIONS OF BOILERS AND VENTING SHOULD

BE DONE ONLY BY A QUALIFIED EXPERT AND IN ACCORDANCE WITH THE
APPROPRIATE OLSEN TECHNOLOGY, INC.  MANUAL.  INSTALLING OR VENTING
A BOILER OR ANY OTHER GAS APPLIANCE WITH IMPROPER METHODS OR
MATERIALS MAY RESULT IN SERIOUS INJURY OR DEATH DUE TO FIRE OR TO
ASPHYXIATION FROM POISONOUS GASES SUCH AS CARBON MONOXIDE
WHICH IS ODORLESS AND INVISIBLE.

SAFETY SYMBOLS

SAFETY SYMBOLS

SAFETY SYMBOLS

SAFETY SYMBOLS

SAFETY SYMBOLS

The following defined symbols are used throughout this manual to notify the

reader of potential hazards of varying risk levels.

DANGER

DANGER - Indicates an imminently hazardous situation which, if not avoided, 

WILL

 result

in death or serious injury.

WARNING

WARNING

 - Indicates a potentially hazardous situation which, if not avoided, 

COULD

result in death or serious injury

CAUTION

CAUTION

 - Indicates a potential hazardous situation which, if not avoided, 

MAY

 result

in minor or moderate injury. It may also be used to alert against unsafe practices.

  IMPORTANT

!

 

READ ALL INSTRUCTIONS BEFORE INSTALLING.

READ ALL INSTRUCTIONS BEFORE INSTALLING.

READ ALL INSTRUCTIONS BEFORE INSTALLING.

READ ALL INSTRUCTIONS BEFORE INSTALLING.

READ ALL INSTRUCTIONS BEFORE INSTALLING.

WARNING

:

1. Keep boiler area clear and free from combustible  materials, gasoline and other

flammable vapors and liquids.

2. 

DO NOT

 obstruct air openings to the boiler room.

3. Modification, substitution or elimination of factory equipped, supplied or specified

components may result in property damage, personal injury or the loss of life.

4. To the owner: Installation and service of this boiler must be performed by a qualified

installer.

5. To the installer: Leave all instructions with the boiler for future reference.

6. For use with No. 2 fuel oil only.

Summary of Contents for OBC Series

























Reviews: