Olivetti d-Color MF220 Copy Operations Download Page 158

Page: 158 / 315

[System Settings]

7-10

d-Color MF360/280/220 (Version 3)

7.1

7.1.7

[Expert Adjustment]

Make adjustments so that output quality is increased.

Press the

Utility/Counter

key

[Administrator Settings]

[System Settings]

[Expert Adjustment].

Settings

[AE Level Adjustment]

Configure the initial value for AE (auto exposure). The higher the setting,
the more that the original background is emphasized.

[Printer Adjustment]

Adjust the starting print position and defective print images caused by pa-
per type features.

Reference

The starting print position is factory-adjusted. Normally, you
are not required to change the set values.

[Leading Edge Adjustment]

p. 7-13

[Centering]

p. 7-13

[Leading Edge Adjustment (Du-
plex Side 2)]

p. 7-13

[Centering (Duplex 2nd Side)]

p. 7-13

[Erase Leading Edge]

Adjust leading edge erase width.
For details on displaying this item,
contact your service representative.

[Vertical Adjustment]

Adjust the feed direction zoom ratio of
paper types.
For details on displaying this item,
contact your service representative.

[Media Adjustment]

p. 7-14

[Finisher Adjustment]

Adjust the staple, folding, and punch position of the

Finisher FS-527

. Oth-

erwise, adjust where to place the paper alignment plate of the

Finisher FS-

529

This item is displayed if the

Finisher FS-527

Finisher FS-529

is in-

stalled.

Reference

Create a sample in advance, and then adjust them while
checking the sample.

[Center Staple Position]

p. 7-14

[Half-Fold Position]

p. 7-15

[Punch Horizontal Position Ad-
justment]

p. 7-15

[Punch Regist Loop Size Adjust-
ment]

p. 7-16

[Paper Alignment Plate Settings]

p. 7-16

Summary of Contents for d-Color MF220




























































































































































































































































































































Search results

Summary of Contents for d-Color MF220

Reviews:

Related manuals for d-Color MF220

Brands by name

Popular brands

Olivetti d-Color MF220, Copy Operations

Search results

Summary of Contents for d-Color MF220

Reviews:

Related manuals for d-Color MF220

Brands by name

Popular brands