Olivetti AK-730 Service Manual Download Page 60

Page: 60 / 155

3NB/3ND/3N0/3NK

1-4-7

6110

DF paper entry sensor stay
jam

DF paper entry sensor (DFPES) is not turned off
within specified time of its turning on (4000-sheet
finisher).

6111

DF paper entry sensor (DFPES) is not turned off
within specified time of its turning on (1000-sheet
finisher).

6120

DF paper entry sensor
remaining jam

DF paper entry sensor (DFPES) does turned on
when the power is turned on or cover close
(4000-sheet finisher).

6121

DF paper entry sensor (DFPES) does turned on
when the power is turned on or cover close
(1000-sheet finisher).

6200

DF sub eject sensor non
arrival jam

DF sub eject sensor (DFSES) does not turn on
within specified time of DF paper entry sensor
(DFPES) turning on.

6210

DF sub eject sensor stay jam

DF sub eject sensor (DFSES) is not turned off
within specified time of its turning on.

6220

DF sub eject sensor remain-
ing jam

DF sub eject sensor (DFSES) does turned on
when the power is turned on or cover close.

6300

DF middle eject sensor non
arrival jam

DF middle eject sensor (DFMES) does not turn
on within specified time of DF paper entry sensor
(DFPES) turning on (4000-sheet finisher).

6301

DF middle eject sensor (DFMES) does not turn
on within specified time of DF paper entry sensor
(DFPES) turning on (1000-sheet finisher).

6310

DF middle eject sensor stay
jam

DF middle eject sensor (DFMES) is not turned off
within specified time of its turning on (4000-sheet
finisher).

6311

DF middle eject sensor (DFMES) is not turned off
within specified time of its turning on (1000-sheet
finisher).

6320

DF middle eject sensor
remaining jam

DF middle eject sensor (DFMES) does turned on
when the power is turned on or cover close
(4000-sheet finisher).

6321

DF middle eject sensor (DFMES) does turned on
when the power is turned on or cover close
(1000-sheet finisher).

6400

DF tray upper surface sensor
non arrival jam

DF tray upper surface sensor (DFTUSS) does not
turn on within specified time of DF middle eject
sensor (DFMES) turning on (4000-sheet finisher).

6401

DF tray upper surface sensor (DFTUSS) does not
turn on within specified time of DF middle eject
sensor (DFMES) turning on (1000-sheet finisher).

Code

Contents

Conditions

Jam

location*

*: Refer to figure 1-4-1 for paper misfeed indication (see page 1-4-1).

Service Manual Y113480-7

Summary of Contents for AK-730



























































































































































Search results

Summary of Contents for AK-730

Reviews:

Related manuals for AK-730

Brands by name

Popular brands

Olivetti AK-730, Service Manual

Search results

Summary of Contents for AK-730

Reviews:

Related manuals for AK-730

Brands by name

Popular brands