Oliver 4045 Owner'S Manual Download Page 11

 

 

Leveling Table Insert 

 

 

 

Adjust the table insert flush with the table by 
turning the four leveling screws (C, Figure 16).  
Place a straight edge across the table and 
insert.  Raise the insert until it just touches the 
straight edge.  Check both the front and rear 
section of the insert. 

 
 

 

 

Splitter and Blade Guard Assembly 

 

The table saw comes equipped with both a 
riving knife and blade guard (see Figure 17).  It 
is always recommended to use the blade guard 
whenever possible.  However, when doing 
narrow cuts when the guard would interfere with 
the fence or any other cuts in which the blade 
guard would pose a problem, replace the guard 
with the riving knife.  Installation is the same for 
both.  For ease of installation, the blade guard 
can be disassembled by loosening the lock knob 
and separating the splitter from the guard as 
shown in Figure 18.  It may be necessary to 
loosen the two screws as indicated in the 
picture. 

Figure 17 

 
 

 

 
1. 

Disconnect saw from power source.  

 

 
2.  Remove table insert by loosening the screw 

at the front of insert.     

 
3.  Loosen the lock nut then insert the fork of 

the riving knife between the nut head and 
backing plate as shown in Figure 19.  Lock 
into place. 

 
4.  Re-install the table insert. 

Figure 18 

 

 

 

 

 

 

Figure 16

 

Figure 19 

 
 

 

 

 

 

 

 

 

11

Summary of Contents for 4045

















Reviews: