background image

3

INSTALLATION

(SECTION DEDICATED TO THE INSTALLER)

RULES AND REGULATIONS

· Read this manual carefully as it contains important indications and instructions concerning the installation, use, maintenance and

safety of the product.

· This appliance must only be installed and used in a room deemed suitable by the specific authorities and in compliance with the

relevant rules and regulations.

· The technological systems and the installation of the appliance must be done by professional qualified personnel authorised to

release the certificate of conformity and compliance with the regulation in force.

· All the laws, rules and regulations in force concerning civil and industrial buildings must be respected, always using PPE and other

means foreseen by law.

· All laws, rules and regulations concerning the systems, chimney flues, electricity, water, ventilation and aspiration must be respected.

· The manufacturer declines all responsibility arising from incorrect installation, tampering, incorrect use of the

appliance, improper use, poor maintenance, and failure to respect regulations in force.

PRELIMINARY OPERATIONS

· Carefully remove the packing.

· The packing material must be recycled by disposing in the special containers or in the local municipal waste disposal site.

· Before installation, make sure that the appliance is intact, in case of doubt, do not use it and contact the vendor.

· Take the containment grill inside the firebox and position it in the special seats as illustrated in figure 1A.

· Take the smoke discharge collar inside the firebox and place it in the special seat in the upper plate as shown in figure 1B.

POSITIONING THE APPLIANCE

· The place where the appliance is installed must have:

- A floor suitable for supporting a weight greater than that of the appliance. If the existing building is not suitable, appropriate

measures must be taken (e.g. a load distribution plate);

- Flooring suitable for heat dispersion which protects the building against fire risks;

- The installation of the appliance must guarantee easy access for its cleaning, the cleaning of the exhaust gas ducts and the

chimney flue;

- The appliance must be positioned on a horizontal surface;

- A minimum distance from adjacent inflammable material;

- A permanently ventilated room in accordance with the regulations in force.

PROTECTION OF THE FLOOR

· The appliance must rest on a refractory surface. In the case of inflammable flooring (wood, carpet, etc.) prearrange a refractory

base (steel sheet, tiles or similar) with the following size:

- Frontal protrusion 

≥≥

≥≥

 

500 mm;

- Side protrusion 

≥≥

≥≥

 300 mm;

- Rear protrusion 

≥≥

≥≥

 100 mm.

1

1.1

1.2

1.3

1.4

1

1

A

B

Summary of Contents for VIVA













Reviews: