manualshive.com logo in svg

Olicom Broadband Wireless Router None, Introduction, Page: 2 / 5

Share
Download
Olicom Broadband Wireless Router None Introduction Download Page 2

Packet Contents 

 

• 

• 

• 

• 

Broadband Wireless Router (AP)       
Power Adapter 
RJ-45 Ethernet Cable                       
Quick Started Guide and User Manual CD 

 

Hardware 

Front panel 

The following illustration shows the front panel of the Broadband Wireless Router (AP): 

1.  When link is established, the LED is 

On

. 

2.  When the device is transferring data, the LED is 

Blinking

.  

 

 

 

 

  Rear Panel  

The following figure illustrates the rear panel of your Broadband Wireless Router (AP). 

 

PWR: 

Power Switch. 

- 
- 

- 

- 

- 

WAN:

 This RJ-45 10 Base-T port connects to an Ethernet port of xDSL/ATU-R broadband 

device. 

LAN port L1/L2/L3/L4: 

10/100 Base-TX, 4 port auto-sensing & crossover Ethernet switching 

hub (LAN interface). 

12VDC:

 12V power connector. 

RST:

 Factory default reset switch. 

To restore factory defaults, you do not need to power off the device. Push a small, stiff object into 
the 

RST 

hole to press down the button. Keep pressing and wait fort 3 seconds (the DIAG LED will 

illuminate about 3 seconds and turn off) to release the button. The device will automatically restart. 
During restart, 

do not 

turn on/off the device and wait for the device to boot up. 

2 

Summary of Contents for Broadband Wireless Router None






Reviews:

No comments