background image

46

Monitor

This item provides the current information about the operation of ADSL
router and there are three options (Route, ADSL and ATM) for you to
monitor.

Click the 

OK 

button to start monitoring selected items, and the status

will display in tables on right side of main page. Or click 

Cancel

 button

to return to main page.

Routing table 

No.  Type  Network Address  Netmask 

Gateway  

Interface 

Port Name 

1 C 192.168.1.0 

255.255.255.0 192.168.1.0 192.168.1.0  IF0 

2 C 127.0.0.1 

255.255.255.255 

127.0.0.1 

127.0.0.1 

Loopback 

3    

 

 

 

 

4    

 

 

 

 

5    

 

 

 

 

6    

 

 

 

 

7    

 

 

 

 

8    

 

 

 

 

9    

 

 

 

 

10  

 

 

 

 

 

ADSL Generic 

Name 

Result 

Buid-in Diagnostic Test 

Successful 

DME Register Read/Write Test 

Successful 

SW Status 

R-QUIET 

Init Status 

Successful 

C-ACT-REQ Not 

Detected 

ADSL Bit Rate 

Item 

Actual(kbps) 

Max(kbps) 

Up Stream Duplex 

Down Stream Duplex 

Down Stream Simplex 

ATM 

No.  IP Address  Netmask 

VPI 

VCI  Encapsulation  Link Type 

Status 

1 192.168.1.1 

255.255.255.0 0  33  LLC 

Ethernet 

Down 

2  

 

 

 

 

 

 

3  

 

 

 

 

 

 

4  

 

 

 

 

 

 

5  

 

 

 

 

 

 

6  

 

 

 

 

 

 

7  

 

 

 

 

 

 

8  

 

 

 

 

 

 

Summary of Contents for ADSL Router A400A























































Reviews: