background image

2

Overloading

Do not overload wall (mains) outlets and extension cords as this can
result in the risk of fire or electric shock.

Servicing

To reduce the risk or electric shock, do not disassemble this product.
None of its parts are user-replaceable; therefore, no reason exists to
access the interior.  Opening or removing cover may expose you to
dangerous voltages or other risks.  Incorrect reassembly can cause
electric shock when the appliance is subsequently used.

If service or repair work is required, take it to qualified service personnel.

Damage requiring service

Unplug the computer from the wall outlet and refer servicing to qualified
service personnel under the following conditions:

y

If liquid has been spilled into the product;

y

If the product has been exposed to rain or water;

y

If the product does not operate normally by following the operating

instructions;

y

If the product has been dropped or damaged in any way;

y

If the product exhibits a distinct change in performance.

Modem/Telephone use

Avoid using a modem/telephone (other than a cordless type) during an
electrical storm.  There may be a remote risk of electric shock from
lightning.

Do not use the telephone to report a gas leak in the vicinity of the leak.

If telephone service is required on the same line and for optimum
ADSL performance or distributed filters must be installed.  Depending
on your ADSL configuration and type of filters, installation must be
carried out by qualified service personnel.  Consult your Telephone
Company of ADSL Service Provider for instructions.

SAVE THESE INSTRUCTIONS

Summary of Contents for ADSL Router A400A























































Reviews: