Oleo-Mac 937 Operators Instruction Book Download Page 18

18

19

2% - 50:1

4% - 25:1

(cm

3

)

(cm

3

)

1
5

10
15
20
25

0,02
0,10
0,20
0,30
0,40
0,50

(20)

(100)
(200)
(300)
(400)
(500)

0,04
0,20
0,40
0,60
0,80
1,00

(40)

(200)
(400)
(600)
(800)

(1000)

20

17

p.n. 4175158

18

001001535

001001362

001001361

001001536

Italiano

English

Français

AVVIAMENTO

STARTING

MISE EN ROUTE

CARBURANTE

Questo prodotto è azionato da un motore a 2 tempi e richiede 

la premiscelazione di benzina e olio per motori a 2 tempi.  

Premiscelare la benzina senza piombo e l’olio per motori a due 

tempi in un contenitore pulito approvato per la benzina (Fig.17). 

CARBURANTE CONSIGLIATO: QUESTO MOTORE È CERTIFICATO 

PER FUNZIONARE CON BENZINA SENZA PIOMBO PER USO 

AUTOMOBILISTICO A 89 OTTANI ([R + M] / 2) O CON UN NUMERO 

MAGGIORE DI OTTANI (Fig.18).

Miscelare l’olio per motori a 2 tempi con la benzina secondo le 

istruzioni sulla confezione.

Consigliamo di usare olio per motori a 2 tempi Oleo-Mac al 2% 

(1:50) formulato specificamente per tutti i motori a due tempi 

raffreddati ad aria Oleo-Mac.

Le proporzioni corrette di olio/carburante indicate nel prospetto 

(Fig.19) sono idonee quando si usa olio per motori Oleo-Mac 

PROSINT 2 e EUROSINT 2 (Fig.20) o un olio motore di alta qualità 

equivalente  (specifiche JASO FD o ISO L-EGD). Quando le 

specifiche dell’olio NON  sono equivalenti o non sono note, usare 

un rapporto di miscelazione olio/carburante del 4% (1:25).

CAUTELA: NON USARE OLIO PER AUTOVEICOLI O OLIO PER 

MOTORI FUORIBORDO A 2 TEMPI.

CAUTELA: non usare mai un carburante con una 

percentuale di alcool maggiore del 10%; sono accettabili  

gasohol con una percentuale di alcool fino al 10% o 

carburante E10.

CAUTELA:

Acquistare solo il quantitativo di carburante necessario 

in base ai propri consumi; non acquistarne più di quanto 

se ne userà in uno o due mesi;

Conservare la benzina in un contenitore chiuso 

ermeticamente, in un luogo fresco e asciutto.

NOTA:  l’olio per motori a due tempi contiene stabilizzatore per 

carburante e rimane fresco per 30 giorni. NON miscelare quantitativi 

maggiori di quelli utilizzabili in un periodo di 30 giorni. Si consiglia 

olio per motori a 2 tempi contenente stabilizzatore per carburante 

(Emak ADDITIX 2000 - cod. art. 001000972 – Fig.21).

RIFORNIMENTO (Fig.23)

Agitare la tanica della miscela prima di procedere al rifornimento 

(Fig.22).

FUELING
This product is powered by a 2-cycle engine and requires pre-
mixing gasoline and 2-cycle oil.  Pre-mix unleaded gasoline and 
2-cycle engine oil in a clean container approved for gasoline 
(Fig.17).
RECOMMENDED FUEL: THIS ENGINE IS CERTIFIED TO OPERATE ON 
UNLEADED GASOLINE INTENDED FOR AUTOMOTIVE USE WITH AN 
OCTANE RATING OF 89 ([R + M] / 2) OR HIGHER (Fig.18).
Mix 2-cycle engine oil with gasoline according to the instructions 
on the package.
We strongly recommend the use of 2% (1:50) Oleo-Mac two cycle 
engine oil, which is specifically formulated for all Oleo-Mac air-
cooled two-stroke engines.
The correct oil / fuel proportions shown in the table (Fig.19) 
are suitable when using the Oleo-Mac PROSINT 2 and 
EUROSINT 2 (Fig.20) or an equivalent high-quality engine oil 
(JASO specification FD or ISO specification L-EGD).When oil 
specifications are NOT equivalent or unknown use 4% (1:25) oil / 
fuel mixing ratio.

CAUTION: DO NOT USE AUTOMOTIVE OIL OR 2-CYCLE 
OUTBOARD OIL.

CAUTION: Never use a fuel with an alcohol percentage 
higher than 10%; gasohol up to 10% alcohol or E10 fuel 
are acceptable.

CAUTION:

Match your fuel purchases to your consumption; don’t 

buy more than you will use in one or two  months;
Store gasoline in a tightly-closed container in a cool, dry 

place.

NOTE: 2-cycle engine oil contains a fuel stabilizer and will stay fresh 
up to 30 days. DO NOT mix quantities larger than usable in a 30 day 
period. A 2-cycle oil containing a fuel stabilizer is recommended 
(Emak ADDITIX 2000 p.n. 001000972 – Fig.21).

FILLING THE TANK (Fig.23)
Stir the mixture well before refuelling (Fig.22).

CARBURANT

Cet appareil est actionné par un moteur 2 temps et nécessite le 

prémélange d'essence et d'huile pour moteurs 2 temps. Prémélangez 

l'essence sans plomb et l'huile pour moteurs 2 temps dans un 

récipient propre homologué pour contenir de l'essence (Fig.17). 

CARBURANT CONSEILLÉ : CE MOTEUR EST CERTIFIÉ POUR ÊTRE 

ALIMENTÉ EN ESSENCE SANS PLOMB POUR USAGE AUTOMOBILIE 

AVEC NIVEAU D'OCTANES 89 ([R + M] / 2) OU SUPÉRIEUR (Fig.18).

Mélangez l'huile pour moteurs 2 temps avec l'essence en suivant 

les instructions sur l'emballage.

Il est conseillé d'utiliser de l'huile pour moteurs 2 temps Oleo-Mac 

à 2% (1:50) spécialement formulée pour tous les moteurs 2 temps 

refroidis par air Oleo-Mac.

Les proportions correctes huile/essence illustrées dans la notice 

(Fig.19) sont adaptées à l'utilisation d'huile pour moteurs Oleo-Mac 

PROSINT 2 et EUROSINT 2 (Fig.20) ou d'huile moteur de haute 

qualité équivalente (spécifications JASO FD ou ISO L-EGD). Quand 

les spécifications de l'huile NE SONT PAS équivalentes ou ne sont pas 

connues, utilisez un rapport de mélange huile/essence de 4% (1:25).

AT T E N T I O N   :   N E   PA S   U T I L I S E R   D ' H U I L E   P O U R 

AUTOMOBILES OU POUR MOTEURS HORS-BORD 2 TEMPS.

ATTENTION : N'utilisez jamais de carburant dont 

le pourcentage d'alcool dépasse 10% ; le gazole avec 

pourcentage d'alcool jusqu'à 10% ou l'essence E10 sont 

acceptés.

ATTENTION :

 N'achetez que la quantité de carburant nécessaire en 

fonction des consommations personnelles ; n'en achetez 

pas plus qu'il n'en sera utilisé en un ou deux mois ;

 Conservez l'essence dans un récipient hermétique, dans 

un endroit frais et sec.

REMARQUE : l'huile pour moteurs 2 temps contient un stabilisateur 

pour carburant et reste fraîche pendant 30 jours. NE mélangez PAS 

des quantités supérieures à celles utilisables sur une période de 30 

jours. Il est recommandé d'utiliser une huile pour moteurs 2 temps 

contenant un stabilisateur pour carburant (Emak ADDITIX 2000 - 

réf. art. 001000972 – Fig.21).

RAVITAILLEMENT (Fig.23)

Secouez le jerrycan du mélange avant de procéder au ravitaillement 

(Fig.22).

BENZINA - ESSENCE
GASOLINE - BENZIN

GASOLINA - BENZINE

OLIO - HUILE - OIL
ÖL - ACEITE - OLIE

Summary of Contents for 937





























































Reviews: