OKUtools EP-8 Operating Instructions Manual Download Page 3

English 

 

Stud Gun EP-8, EP-9, EP-10 

 OKU Tools GmbH, 71229 Leonberg, Germany 

EN 

 

1 Preface and general information 

1.1 General 

The operating instructions is used for safe operation of the Stud Guns (in the follow-
ing  referred  to  as  “gun“)  type  Automatic  Stud  Gun  EP-8,  EP-9  and  EP-10  (ID-No. 
100192, 100193, 100194, 101758, 100262, 100263)). The safety instructions includ-
ed hereinafter must be observed. 

The operating instructions must be available for anybody who is working with the gun 
and the included instructions must be carefully attended to. 

The operating instructions must always be complete and perfectly readable. 

1.2 Scope of supply 

The delivery normally consists of a stud gun, the operating instruction and 1 separat-
ing  finger for  multi-flange  studs fingers  (only  EP-8  and  EP-9). The  parts  included  in 
your delivery are stated in the accompanying papers. 

These papers shall be checked for conformity, immediately after receipt of the goods. 
OKU Tools GmbH does not provide any guarantee and/or accept any liability for de-
fects complained belatedly. Therefore: 

  Contact the forwarder immediately to complain visible transit damages. 

  Contact OKU Tools GmbH immediately to complain visible defects and/or incom-

pleteness of delivery. 

1.3 Intended use 

The gun is intended to be used only for the insertion of single and multi-flange spikes 
into tyres of cars. 

Any other use shall be deemed to be inappropriate! 

1.4 Liability 

The  information,  data  and  notes  of  this  operating  instruction  were  up-to-date  when 
passing for press. The specifications, illustrations and descriptions included hereinaf-
ter do not apply for any previously supplied guns. 

We do not accept liability for damages and operating troubles caused by: 

  inappropriate use. 

  unauthorized modification of gun. 

  improper operation of the gun. 

  operating errors. 

  disregard of this operating instructions. 

Summary of Contents for EP-8



















Reviews: