manualshive.com logo in svg

Oktober MK16s, Operation Manual, Page: 3 / 20

Share
Download
Oktober MK16s Operation Manual Download Page 3

!!!SAFETY PRECAUTIONS!!! 

-Since canning is likely to create a wet environment, make sure the flooring 
around the seamer is non-slip.   

-Always plug the seamer into a GFCI outlet to avoid shocking hazards. 

-Pay attention to things like loose clothing, long hair, etc. The can and upper and 
lower chucks will be spinning and can cause injury if anything gets wrapped 
around them.   

-Never reach into area around the upper chuck and rollers while operating.  The 
rollers can pinch or draw-in fingers and objects and cause injury. 

-Never remove the top cover while operating.  The spinning belt and motor will be 
exposed and can cause injury.   

-Never remove the switch enclosure box, or the motor connection panel while the 
seamer is plugged in.  There are open live connections inside each that risk a 
shocking hazard.   

------------------------------------------------------------------------------------------------------------- 

POWER REQUIREMENTS 

Short Circuit Current Rating: 

120V:  

 

220V: 

Rated Frequency 

120V: 60Hz   

220V: 50Hz 

Full Load Current 

120V:  

 

220V: 

------------------------------------------------------------------------------------------------------------- 

 

 

Summary of Contents for MK16s





















Reviews:

No comments