Okolab UNO-T Manual Download Page 48

Page: 48 / 73

8.2.5.3

Obj. Heater

Press on

Obj

icon

, to enter the Objective Heater calibration submenu (see Figure 62).

Note

►

Make sure that the Objective Heater is enabled (see paragraph 8.2.3).

Figure 62. Settings

–

Calibrations - Obj. Heater (a

–

b).

At this point you can choose:

By pressing

Log

button (see pointer 1 in Figure 62 b) you can select parameters obtained by calibrations

previously performed (see Figure 63 b).

Figure 63. Settings

–

Calibrations

–

Obj. Heater - Log (a

–

b).

By pressing

Factory

button (see pointer 2 in Figure 62 b) UNO-CONTROLLER will recover the factory

offset.

To perform the

Manual

procedure, follow the instructions below:

Note

►

Make sure that a Chamber Calibration has been performed (see paragraph 8.2.5.1).

•

Make sure that T Sensor is connected to UNO-CONTROLLER (see paragraph 7.4).

•

Secure with commercial adhesive tape the T Sensor to the bottom of the sample holder you use during
standard operation (Petri dish, Chambered Glass Slide, etc.) as shown in Figure 64. Do not cover the

tip of the T-Sensor with the adhesive tape.

Summary of Contents for UNO-T










































































Search results

Summary of Contents for UNO-T

Reviews:

Related manuals for UNO-T

Brands by name

Popular brands

Okolab UNO-T, Manual

Search results

Summary of Contents for UNO-T

Reviews:

Related manuals for UNO-T

Brands by name

Popular brands