Okolab H301-PI-736-160x110 User Manual Download Page 3

Page: 3 / 17

H301-PI-736-160x110

User Manual

REV 03

www.oko-lab.com

Components and dimensions

H301-PI-736-160x110 includes the following components:

•

Chamber main body

with embedded temperature sensor. It connects to the piezo stage with screws.

•

Sliding heated glass lid

with Indium Tin Oxide (ITO) conductive coating and embedded temperature sensor

•

Chamber riser

. It is a removable frame increasing the height of the chamber from 27 to 33 mm, often re-

quired when using multi-well (MW) plates.

Distance between focal plane

and upper side of the glass

lid without the chamber riser

Distance between focal plane

and upper side of the glass

lid with the chamber riser

Chamber top view

Sliding Lid

Chamber Riser

Chamber Base

Sample Holder-Order Separately

Figure 1. H301-PI-736-160x110 - Components and Dimensions.

Available Sample Holders

The following sample holders are available.

NOTE:

Please contact

[email protected]

if you cannot find the sample holder you are looking for. We are constantly

adding new inserts to the list.

1x35-M

#1 35mm Petri-dish

1xGS-M

#1 1x3in. chamber slide

1xLABTEK-M

#1 Lab-Tek 1in.x2in. chambered cover glass

1xLABTEK-II-M

#1 Lab-Tek II 1in.x2in. chambered cover glass

1x60-M

#1 60mm Petri-dish

1xT25-M

#1 Nunc and Greiner T25 flask

2x35-M

#2 35mm Petri-dish

2xGS-M

#2 1x3in. chamber slides

2xLABTEK-M

#2 Lab-Tek 1in.x2in. chambered cover glass

2xLABTEK-II-M

#2 Lab-Tek II 1in.x2in. chambered cover glass

2x60-M

#2 60mm Petri-dish

4x35-M

#4 35mm Petri-dish

Summary of Contents for H301-PI-736-160x110


















Search results

Summary of Contents for H301-PI-736-160x110

Reviews:

Related manuals for H301-PI-736-160x110

Brands by name

Popular brands

Okolab H301-PI-736-160x110, User Manual

Search results

Summary of Contents for H301-PI-736-160x110

Reviews:

Related manuals for H301-PI-736-160x110

Brands by name

Popular brands