manualshive.com logo in svg

Oki ML5521, User Manual, Page: 27 / 95

Share
Download
Oki ML5521 User Manual Download Page 27

USING YOUR PRINTER > 27

PRINTER RESET

Clearing some error conditions requires that you reset (reinitialise) 
the printer. To do this:

1.

Press and release 

SEL

 (1) to take the printer off-line.

The 

SEL

 light goes out.

2.

Press and hold 

SHIFT

 

(2), then press the 

RESET/CHARACTER 

PITCH

 key (5).

EMULATIONS

l

IBM

®

 Proprinter III —

factory setting

l

Epson

®

 FX

l

Oki

®

 MICROLINE

®

Changing Emulations

Make sure paper is loaded.

1.

Press and hold 

SHIFT

 

(2), then press 

SEL

 (1).

2.

Press 

LF

 (3).

The following line will print:

Printer Control

Emulation Mode

IBM PPR

3.

Press 

TEAR

 (4) repeatedly until the emulation you wish to 

select prints in the right-hand column.

4.

Press and hold 

SHIFT

 (2), then press 

SEL

 (1) to save your 

setting and exit the Menu Mode.

NOTE

Pressing 

SHIFT

 and 

RESET

 reinitialises the printer, but does 

not

 affect 

any menu settings and does

 not

 reset the printer to the factory defaults. 

For information on resetting the printer to the factory defaults, see 
“Resetting the Menu to the Factory Defaults” later in this chapter.

1

4

3

2

5

Summary of Contents for ML5521
































































































Reviews:

No comments