Oki MB770 Maintenance Manual Download

Page: 81 / 104

45372301TH Rev.2

6-4 /

Oki Data CONFIDENTIAL

[EA40] Rear cover open jam

[EA50] Stapling jam

Classification

Error content

Paper jam in finisher section

Jam occurred because finisher's rear cover was opened while finisher

was transporting paper.

Check item

Measures

Transport path

If there is paper in the paper transport path, remove the paper.

Rear cover

Close the cover if it is open.

Door switch

• Switch check (SW2)

• Connector check (P2-12, P2-13)

• Harness check

Finisher control PC board

• Board check

• Connector check (J2)

• Harness check

Parts to be replaced

Remark

Door switch

Finisher control PC board

Classification

Error content

Paper jam in finisher section

Staple jam occurred at stapler.

Check item

Measures

Stapler

• Remove the staple cartridge, remove any jammed staples, install the

staple cartridge.

• Connector check (P9-1, P10-1)

• Harness check

Finisher control PC board

• Board check

• Connector check (J9, J10)

• Harness check

Parts to be replaced

Remark

Stapler

Finisher control PC board

Summary of Contents for MB770









































































































Search results

Summary of Contents for MB770

Reviews:

Related manuals for MB770

Brands by name

Popular brands

Oki MB770, Maintenance Manual

Search results

Summary of Contents for MB770

Reviews:

Related manuals for MB770

Brands by name

Popular brands