Oki C9200 Service Manual Download Page 107

Page: 107 / 157

41388601TH Rev.2

107 /

The printer does not work normally after turned on.

•

Turn off the printer, wait a few seconds, then turn it on again.

•

Is displayed on the LCD (for about 1 second)?

•

Is the AC cable connected correctly?

Connect the AC cable correctly.

▼

•

Yes Is +5V supplied to the PANEL connector pins on the PU board (K73 PWB)?

+5V: Pin 5

0V: Pin 2

Yes Is the operator panel cable connected correctly?

Connect the cable correctly.

▼

Yes Replace the operator panel cable. Recovered?

Replace the cover assembly of the operator panel.

▼

Yes End

▼

•

Is +5V supplied on the POWER connector of the engine board (K73 PWB)?
Pin 11,12, 13, 14: +5V Pin 3, 4, 5, 6, 23, 24, 25, 26, 27, 28, 29, 30: 0V

Check the connection of the POWER connector, or replace the low-voltage power
supply unit.

▼

•

Yes Replace the engine board.

▼

•

Yes

Are the following voltages supplied to the PU connector of the main board?
Pin 137-147, 187-197: +5V

Pin 125-136, 175-186: +3.3V

Pin 148, 198: +12V

Pin 101-124, 149-174, 199, 200: 0V

Yes Is the main board assy inserted correctly?

Insert it correctly.

Yes Replace the main board.

▼

•

Are the following voltages supplied on the POWER connector of the engine board?
Pin 11, 12, 13, 14: +5V

Pin 15, 16, 17, 18: +3.3V

Pin 1: +12V

Pin 2: -12V

Pin 7, 8, 9, 10: +32V

Pin 3, 4, 5, 6, 25, 26, 27, 28: 0V

Yes Replace the engine board.

▼

•

Replace the low-voltage power supply unit.

Summary of Contents for C9200






























































































































































Search results

Summary of Contents for C9200

Reviews:

Oki C9200, Service Manual, Page: 107 / 157

Search results

Summary of Contents for C9200

Reviews: