Oki C9200 Service Manual Download Page 102

Page: 102 / 157

41388601TH Rev.2

102 /

Service Call
040: Error

CU EEPROM Error

Can the printer recover from the error by
replacing the EEPROM on the CU board?

Yes

Replace the EEPROM. (Settings of the
user must be restored on the new.)

Replace the CRM board.
(The EEPROM needs replacement.)

Service Call
041: Error

U Flash Error.

On-CU-board Flash
ROM Error

Does the error message appear again?

Yes

Replace the CRM board.

(The EEPROM needs replacement.)

Service Call
050: Error

Operator Panel Error

Does the error message appear again?

Yes

See the flowchart for the problems with

no LCD message displayed.

Service Call
051: Error

CU Fan Error.
On-CU-board CPU
Cooling Fan
Problem

Is the on-CU-board connector connected
properly?

Can the printer recover from the error by
replacing the fan?

Yes

Connect the connector properly.

Replace the fan.

Replace the CRM board.
(The EEPROM needs replacement.)

Service Call
063: Error

Network Comm.Error.
CU ~ NIC H/W I/F
Problem

Is the network board installed properly?

Can the printer recover from the error by
replacing the network board?

Yes

Install the network board properly.

Replace the network board.

Replace the CRM board.
(The EEPROM needs replacement.)

Service Call
070: Error

CANT_HAPPEN.
PS F/W Problem
Detection

Is it recovered by turning the printer off/on.

No Replace the CRM board.

(The EEPROM needs replacement.)

Service Call
072: Error

Engine Communication
Error

PU ~ CU I/F Error

Is the CU Assy installed properly?

Can the printer recover from the error by
replacing the CRM board?

Yes

Install the CU Assy properly.

Replace the CRM board.
(The EEPROM needs replacement.)

Replace the PU board.

Service Call
073: Error
~
075: Error

Service Call
120: Error
~
122: Error

Video Overrun
Detect

Is the CU Assy installed properly?

Can the printer recover from the error by
replacing the CRM board?

Yes

Install the CU Assy properly.

Replace the CRM board.
(The EEPROM needs replacement.)

Service Call

100/100:Error

Error detected at Engine
ROM Checksum when
turned on.

Does the error repeat?

Yes

Replace the PU board.

Replace the engine control board (K73).

Service Call
102: Error

Error detected at Engine
RAM Read/Write when
turned on.

Does the error repeat?

Yes Replace the engine control board (K73).

Service Call
103: Error

Error detected at Engine
SRAM Read/Write when
turned on.

Does the error repeat?

Yes Replace the engine control board (K73).

Service Call
104: Error

Error detected at Engine
EEPROM Checksum
when turned on.

Does the error repeat?

Yes Replace the engine control board (K73).

Service Call
105: Error

EEPROM not detected
when turned on.

No EEPROM?

Does the error repeat?

Yes

Confirm the existence of EEPROM.
Without it, mount an EEPROM.

Replace the engine control board (K73).

Service Call
106: Error

Error detected at Engine
Control Logic.

Does the error repeat?

Yes

Replace the engine control board (K73).

Error detected at the
Power unit cooling fan in
the Controller cavity.

1) Is the error message displayed?

2) Does the error repeat?

Turn off/on the printer.

Replace the Fan motor.

Service Call
123: Error

Inappropriate ambient
RH detected by a
sensor.

1) Is the error message displayed?

2) Does the error repeat?

Turn off/on the printer.

Replace the RH sensor.

Service Call
124: Error

Inappropriate ambient
temp. detected by a
sensor.

1) Is the error message displayed?

2) Does the error repeat?

Turn off/on the printer.

Replace the temperature sensor.

Message

Cause

Error Description

Solutions

Table 6-1-1 Operator Alarms (2/5)

Summary of Contents for C9200






























































































































































Search results

Summary of Contents for C9200

Reviews:

Oki C9200, Service Manual, Page: 102 / 157

Search results

Summary of Contents for C9200

Reviews: