manualshive.com logo in svg

Oki B410, Maintenance Manual, Page: 44 / 171

Share
Download
Oki B410 Maintenance Manual Download Page 44

43984801TH Rev.1 

44 /

Oki  Data  CONFIDENTIAL

3. Parts replacement

3.3.7  OPE Cover-Assy

(1)  Open the Rear-Cover-Assy. 

(2)  Open the Stacker-Cover-Assy. 

(3)  Remove the Cover-Side-R and Cover –Side-L. (Refer to 3.3.3/3.3.4) 

(4)  Remove the Plate-Cover-Shield-CU. (Refer to 3.3.5(2)) 

(5)  Remove the screw (Silver) 

①

. Remove the Film-Core-Holder 

②

. 

(6)  Remove the FFC cable 

③

 from the CU board. 

(7)  Open the Cover-Assy-MPT. 

(8)  Pull  Claw  A  by  the  arrow  direction.  Remove  the  clamp  by  pushing  Claw  B  as  the  arrow  direction.  

Remove the OPE Cover-Assy 

❹

. 

(9)  Installing is performed by the reverse procedure with removing.

(Note on removing / installing)

1.  Beware of not to touch the DC motor inattentively (Do not rotate motor).

①

②

③

CU board

Stacker-Cover-Assy

Rear-Cover-Assy

Cover-Assy-MPT

❹

Claw A

Claw B

Claw B

Summary of Contents for B410












































































































































































Reviews:

No comments