EN
8
Initial setup
Initial setup involves selecting all the settings
required to be able to search for and store all the
analogue and digital channels you can receive.
Make sure that the television is switched on and
follow all the steps in turn specified hereafter.
Note: If the channel search retrieved only the
analogue channels it could be caused by poor
broadcasting and therefore is not covered
by manufacturer warranty. Manufacturers
cannot be held responsible for lack of or poor
broadcasting in some areas.
The first time you switch the set on, the
Initial
setup
wizard opens, which guides you through
the initial setup process. (Refer to Figure 1.)
1.
Press
▲
/
▼
to select your language, then press
OK/
►
to enter the next step.
2.
Press
▲
/
▼
to select your country, then press
OK/
►
to enter the next step.
Note: If you select
France
, you will have to
enter the
Password setting
menu here in
order to set a password. Use the
numeric
buttons to enter a four-digit number for
your password. (0000 is too simple to
be set as your password.) Re-enter the
same code to confirm the password.
After that, you will enter the next step
automatically. (In this step, you can only
press
◄
to return to the previous step.)
3.
Press
▲
/
▼
to select your tuner mode
Antenna
or
Cable
.
- Select
Antenna
.
• Press
OK/
►
to enter.
• Press
▲
/
▼
to select
Scan
, then press
OK/
►
to start the automatic search for all DVB-T
digital
and/or analogue channe
ls.
- Select
Cable
.
• Press
OK/
►
to enter.
• Press
▲
/
▼
to select
Scan
, then press
OK/
►
to directly start your initial setup or enter
below step.
• Select
Full
if available
to search for and store
all DVB-C digital and analogue channels.
• You may select another advanced
scan mode if available (for example,
Advanced
), then configure
the correct
cable information as described below. Use
the
numeric
buttons to adjust the values
for frequency, symbol rate and network
ID; use
◄
/
►
to select a modulation mode.
• Press
OK
to start initial setup relating to
all DVB-C digital and analogue channels.
Note: To prevent the channel setup process from
being interrupted, wait for the message
indicating that the setup is complete.
4.
Before starting the scanning, you can also select
Skip scan
to skip the initial setup process.
5.
During the setup, you can follow the hints
available at the bottom of the screen to return
to the previous step by pressing
◄
. Or press
Exit
to exit or interrupt the search halfway.
6.
Once the automatic search ends, the set
enters the next step automatically. Press
▲
/
▼
to select your location
Shop
or
Home
. Press
OK/
►
to confirm your selection and enter the
last step.
7.
- In this step, you can press
OK
to exit the
initial setup. The channels are arranged in
a preset order. If you wish to skip channels,
modify the preset order or rename channels,
select
Setup > Organiser
and press
OK/
►
to
enter.
- In this step, you can also press
◄
to return to
the previous step.
Performing an automatic channel search
This section describes how to search and store
channels automatically. Instructions are for both
analogue and digital channels.
1.
Press
Menu
on the remote control and select
Setup > Language > Menu language
. Press
◄
/
►
to select your desired menu language.
2.
Press
Menu
to return to
Setup
, press
▲
/
▼
to
select
Country
, then press
◄
/
►
to select your
country. The TV installs and arranges channels
according to your country.
3.
Press
▲
/
▼
to select
Tuner mode
, then
press
◄
/
►
to select
Antenna
or
Cable
.
- Select
Antenna
.
• Press
▲
/
▼
to select
Channel install
, and
press
OK/
►
to enter.
• Select
Automatic search
(Refer to
Figure 2.), then press
OK/
►
to display
Automatic search
.
• Press
OK
to skip the country selection and
enter the next step. Or use
◄
/
►
to reselect
your country, then press
OK
to enter.
• Select
Digital &
Analogue
,
Digital
or
Analogue
, then press
OK/
►
to start the
automatic search, which relates to all DVB-T
digital and/or analogue channels.
- Select
Cable
.
• Press
▲
/
▼
to select
Channel install
, and
press
OK/
►
to enter.
• Select
Automatic search
, then press
OK/
►
to display
Automatic search
.
• Press
OK
to skip the country selection and
enter the next step. Or use
◄
/
►
to reselect
your country, then press
OK
to enter.
• - Select
Digital &
Analogue
, then press
OK/
►
to enter. Select your scan mode
if available and configure proper cable
information in the same way as in Initial
setup. Select
Scan
and press
OK/
►
to
start your automatic search relating to all
DVB-C digital and analogue channels.
Installing channels
Chapter 3
