background image

event. Transport damages are not covered by the warranty. The warranty does not

cover issues caused by incorrect installation at the place of use or installation contrary

to the installation or operation manual, or issues resulting from repair, modification, or

installation of Products by some other party than the manufacturer or a maintenance

company authorized by the manufacturer.

The warranty does not cover the adjustments or bleeding of air indicated in the Product

operation manual. Furthermore, the warranty does not cover any faults caused by use

of unauthorized and corrosive fluids in the system.

The Supplier grants only the warranty specified above and, consequently, the warranty

described herein comprises the entire warranty granted by the Supplier for the

Products. The warranty shall not cover any additional equipment installed in the

Products at a later date or accessories that are subject to their own warranty.

Procedure in case of a defect

The Customer shall notify the seller or the Supplier of the defect in writing within

reasonable time and, at the latest, 21 days of noticing the defect or the Customer

should have become aware of the defect.

The Customer shall, to the best of their ability, limit the damage caused by the defect.

The Supplier shall not be liable for damages to the extent that they could have been

avoided through the Customer’s careful and appropriate conduct.

Limitation of liability

The Supplier shall not, under any circumstances, be liable for indirect damages,

excluding damages that the Supplier has caused with willful intent or gross negligence.

The Supplier’s maximum liability is always limited to the value of the delivered

Products. To the extent that claims are raised against the Supplier based on product

liability damages for which the Supplier could be liable, the Supplier’s liability shall be

limited to the extent of common product liability warranty terms.

Force Majeure

If the Supplier is prevented from fulfilling its obligations in accordance with this contract

due to a reason that is considered a force majeure event and that is not dependent on

the manufacturer, such as war, civil commotion, industrial action, epidemic, fire, natural

forces, government actions, events preventing the procurement of raw materials,

or an accident in production, warehousing or transport, or any other reason that

is comparable to these, the Customer is not entitled to claim for compensation in

accordance with this contract or any other indemnity from the Supplier.

Applicable law and settlement of disputes

These terms of sale and warranty and/or other agreements between the Seller and the

Customer shall be governed by the Laws of Finland. Any dispute, controversy or claim

arising out of or relating to this contract, or the breach, termination or validity thereof,

shall be finally settled by arbitration in accordance with the Rules for Arbitration of the

Finland Chamber of Commerce. The seat of arbitration shall be the District Court of

South Ostrobothnia.

20 (20)

M8015 2337EN

Summary of Contents for OilonCooling Ck5






























Reviews: