background image

13

Technical specifications

Fork lengths and diameters

Front fork Motorcycle Length (L)

ØA

ØB

FG 012

GasGas

938 mm

53,9 mm

58,4mm

Rebound and compression adjustment

Refer to mounting instruction for set-up data.
Maximum open rebound and compression valve: 20
clicks.

Free Spring Length:

All forks: 467 mm (service limit 460 mm).

Spring preload:

Maximum allowed adjustment
range 3-13 mm (with washers).

Spring rate:

All forks:

2328-41 4,1 N/mm.
2328-43 4,3 N/mm supplied

Optional spring rate:

2328-39: 3,9 N/mm.
2328-45: 4,5 N/mm.
2328-47: 4,7 N/mm

Oil level:

See mounting instruction for recommended oil level.
Adjustment range 90-130 mm.

CAUTION

!

Use only Öhlins high performance front fork fluid No.
5 (1305-01).

Loctite glue:

542 for fork bottom thread and cartridge top lid.

Tighten torque:

Triple clamp bolt: See your bike's work shop manual.
Compression valve: 65 Nm (Base valve).
Cylinder tube lid (cartridgetube): 65 Nm
Compression valve, 8 mm nut 8 Nm.
Rebound valve, 8 mm nut 8 Nm.

Grease:

Öhlins Front Fork grease 148-01
(Green grease).

Service Intervals:

Every 20 hours.

Service tools

Pos.

Part No.

Description

1

1799-02

Bushing/seal mounting tool

2

0786-03

Inner tube tool

3

1797-01

Tool-cylinder tube lid

4

0787-03

Cylinder tube tool (cartridge)

5

1702-02

Bushing remover tool

1

2

3

4

5

ØA

ØB

L

70

300

200

Summary of Contents for FG 012 GasGas

















Reviews: