background image

Ranger™ Count 3000 Series    

      EN-35

Disposal 

In conformance with the European Directive 2002/96/EC on Waste Electrical 

and Electronic Equipment (WEEE) this device may not be disposed of in 

domestic waste. This also applies to countries outside the EU, per their specific 

requirements. 

The Batteries Directive 2006/66/EC introduces new requirements from 

September 2008 on removability of batteries from waste equipment in EU 

Member States. To comply with this Directive, this device has been designed for 

safe removal of the batteries at end-of-life by a waste treatment facility. 

Please dispose of this product in accordance with local regulations at the collecting point 

specified for electrical and electronic equipment. If you have any questions, please contact 

the responsible authority or the distributor from which you purchased this device. 
Should this device be passed on to other parties (for private or professional use), the content 

of this regulation must also be related. 
Disposal instructions in Europe are available online. 
Thank you for your contribution to environmental protection. 

FCC Note 

This equipment has been tested and found to comply with the limits for a Class B digital device, 

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable 

protection against harmful interference when the equipment is operated in a commercial 

environment. This equipment generates, uses, and can radiate radio frequency energy and, if 

not installed and used in accordance with the instruction manual, may cause harmful 

interference to radio communications. Operation of this equipment in a residential area is likely 

to cause harmful interference in which case the user will be required to correct the interference 

at his own expense. 

Industry Canada Note 

This Class B digital apparatus complies with Canadian ICES-003. 

ISO 9001 Registration 

In 1994, OHAUS Corporation, USA, was awarded a certificate of registration to ISO 9001 by 

Bureau Veritus Quality International (BVQI), confirming that the OHAUS quality management 

system is compliant with the ISO 9001 standard’s requirements.  On June 21, 2012, OHAUS 

Corporation, USA, was re-registered to the ISO 9001:2008 standard. 

Summary of Contents for RC31P1502-M







































Reviews: