Ofna Racing X2 TRUGGY Instruction Manual Download Page 4

Running a nitro kit is fun and easy, but to make this a safe 

• Clean oil and dirt from chassis with a degreaser like
Simple Green.

and good experience you must observe a few rules.  This 
kit is extremely fast, easily over 40MPH, and can seriously 

Precautions

injure someone if you are not careful.

• This kit is not a toy.  Always run car with a second 
person as a spotter and pitman.

Where to run car?

• Any running area you choose must be dry.  Do not run 

• Hot Parts - The pipe, manifold, engine and head are very 

car near any water or wet dirt.

hot and will cause burns.

• Do not run on public streets.  It is very easy to have the 
car run over or damaged by hitting the curb.

• Rotating Parts - Keep hands away from the drive train, 

• Do not operate car in tight confined places. The car is 

wheels, and engine when engine is running.

very fast and will easily hit something.
• Do not run near people or animals. 

• Radio - Check batteries life before running the car.  If 

 

radio does not have full control of the car with steering 

 • Due to noise, you will want to consider the surrounding 

and/or throttle/brake do not run until corrected.  Failure to 

area when operating the car.

correct this will result in possible injury and damage to the 

• Do not operate the car at night.  You will not be able to 

car or property.

drive it without hitting something.
• Do not operate the car indoors.  Engine exhaust is not 

• Glow fuel - 

Do not

 leave the glow fuel unattended with 

healthy.

the lid off.  Fuel contains Methanol and Nitro Methane 
both are flammable and poisonous.

Glow Fuel

• Glow fuel is poisonous!

•Store fuel in cool ventilated location.  Refer to the glow 

• Glow fuel is flammable!
• Do not leave in fuel bottle with lid off at any time.

fuel label for additional precautions.

• Do not use any fuel other than glow fuel in this engine.

• Car Fuel tank - Never store fuel in car tank, it will ruin the 

First Time Starting the Engine

engine if left in tank.

Caution! When starting engine make sure the following is 
observed.

• Always turn off the car BEFORE turning off radio.

• Set engine Master needle to 3 turns (rich setting)
• Do not do this alone, get an experienced friend to help at 

• DAMAGE DUE CAR RUN AWAY IS NOT A WARRANTY 

first.

ISSUE.

• Fill fuel tank, try not to spill fuel.  Do not spill fuel on 
receiver

IF YOU DO NOT BREAK-IN ENGINE 

• Hold car off the ground, so it will not runaway when first 

CORRECTLY, MAINLY AT LOW RPM, 

started
• Turn on Radio and check the linkage before starting 

YOU WILL BREAK THE CONNECTING 

engine.

ROD!

• Turn on car receiver battery switch.
• Always have an air filter on the carburetor to keep dirt 
out of engine.

FAILURE TO NOT READ AND 

Engine Break-in

FOLLOW BREAK-IN ENGINE 

• See Engine Page.

Emergency Stopping Engine When Running

INSTRUCTIONS WILL VOID 

• Remove air filter and cover carb. intake.
• Squeeze fuel line and hold until engine stops.

WARRANTY!

• With a rag, cover exhaust outlet.

Storing Car After Running

CHECK RADIO SETTING, 

• Remove fuel from tank and fuel lines
• Turn off radio in car

LINKAGE BEFORE STARTING.

• Put a few drops of after run in engine to keep it from 
rusting.

The car is very fast 

and will too easily hit someone.

MUST READ THIS BEFORE RUNNING

Summary of Contents for X2 TRUGGY




































Reviews: