OfiTE 900 Instruction Manual Download Page 32 | Manualshive

Page: 32 / 58

OfiTE 900 Instruction Manual Download Page 32

Patent No. 6,766,028 - OFI Testing Equipment, Inc.

OFITE, 11302 Steeplecrest Dr., Houston, TX 77065 USA / Tel: 832-320-7300 / Fax: 713-880-9886 / www.ofite.com

31

Software

Saved Test Data

To review test data from past tests:

1. Select “Saved Test Data” from the “File” menu.

2. The saved test data is grouped by month. Select the folder for the year

and month of the data you are looking for and click the small + sign next

to it. This will show you all of the data for tests run that month, including

any comments you added.

3. Select the test you are looking for and click the “OK” button. Multiple

tests can be selected by holding down the CTRL key and selecting each

test.

Saved Experiment Explorer

4. On the “Raw Data” tab you will see the graph of the test results. The

“Analysed Data” tab shows the results of the calculations based on the

Analysis Model. The “Test Setup” tab shows the parameters of the test.

Raw Data

«
...
30
31
32
33
34
...
»

Summary of Contents for 900



























































Reviews:

No comments