Oemtools 24824 Operating Instructions And Parts Manual Download Page 3

3

Operating Instructions and Parts Manual 

24824

4800W 240V  

SHOP HEATER

7/17

2017 OEMTOOLS

2.  Never leave heater unattended while in use. Keep 

children and pets away from heater while in use. 

3.  Always unplug heater when not in use. 
4.  DO NOT operate any heater with a damaged cord 

or plug or after the heater malfunctions, has been 

dropped or damaged in any manner. 

5.  Any repairs to this heater should be carried out by a 

qualified service person.

6.  Under no circumstances should this heater be 

modified. 

7.  DO NOT use outdoors. 
8.  Use your heater only in dry environments. This 

heater is not intended for use in bathrooms, laundry 

areas and similar indoor locations. Never locate the 

heater where it may fall into water. DO NOT use near 

sinks, swimming pools or other damp areas such as 

flooded basements, garages, etc. or anywhere the 

heater could come in contact with water.

9.  DO NOT run cord under carpeting. DO NOT cover 

cord with throw rugs, runners, or similar coverings. 

Arrange cord away from traffic area and where it will 

not be tripped over.

10. To disconnect heater, first turn controls to OFF, then 

remove plug from outlet. Always unplug the heater 

when not in use.

11. Connect to a properly grounded outlet only.

12. DO NOT insert or allow foreign objects to enter any 

ventilation or exhaust opening as this may cause an 

electrical shock, fire, or damage the heater.

13. To prevent a possible fire, do not block air intakes 

or exhaust in any manner. DO NOT use on soft 

surfaces where openings may become blocked.

14. This appliance may have internal arcing or sparks 

that could ignite flammable fumes. DO NOT use it in 

areas where gasoline, paint or flammable liquids are 

used or stored. 

15. Use this heater only as described in this manual. Any 

other use not recommended by the manufacturer 

may cause fire, electric shock, or injury.

16. It is advised to avoid the use of an extension cord 

because the extension cord may overheat and 

cause a risk of fire. 

17. This heater may include an audible or visual alarm to 

warn that parts of the heater are getting excessively 

hot. If the alert sounds or flashes, immediately 

turn the heater off and inspect for any objects 

on or adjacent to the heater that may cause high 

temperatures. DO NOT OPERATE THE HEATER 

WITH THE ALARM ACTIVATED. 

CONTENTS

Heater Assembly, Mounting Bracket, Carry Handle and  

Wireless Remote 

65 mm Screws (3)

M10 mm Screw (1) 

5 mm Nut (1)

20 mm Bolt (1) 

Lock Washer (1) 

10 mm Washer (1)

Wall/Ceiling Bracket (1) 

Handle (1)

16 mm Screws (2) 

5 mm Washers (2) 

Lock Washers (2)

Wireless Remote

A

E & F

B

G

C

D

Heater Assembly

Summary of Contents for 24824









Reviews: