3
Operating Instructions and Parts Manual
24453
OBD2 MEMORY SAVER
• Engine parts that are in motion and unexpected
movement of a vehicle can injure or kill. When working
near moving engine parts, wear snug fit clothing and
keep hands and fingers away from moving parts.
Keep hoses and tools clear of moving parts. Always
stay clear of moving engine parts. Hoses and tools
can be thrown through the air if not kept clear of
moving engine parts. The unexpected movement of
a vehicle can injure or kill. When working on vehicles
always set the parking brake or block the wheels.
• Avoid accidental fire and/or explosion. Do not smoke
near engine fuel and battery components.
• We believe the information contained herein to be
reliable. However, general technical information is
given by us without charge and the user shall employ
such information at his own discretion and risk. We
assume no responsibility for results or damages
incurred from the use of such information in whole or
in part.
• The manufacturer declines any and all responsibility
for damage to vehicles or components if said damage
is the result of unskillful handling by the operator or of
failure to observe the basic safety rules set forth in the
instruction manual.
IMPORTANT SAFETY INSTRUCTIONS
The warnings, precautions, and instructions discussed
in this manual cannot cover all possible conditions and
situations that may occur. The operator must understand
that common sense and caution are factors which
cannot be built into this product, but must be supplied by
the operator.
PURPOSE
The only OBD-II Memory Saver designed for use with
lithium portable power units with fuse and back charge
protection. The OBD2 Memory Saver works with
OEMTOOLS
®
multi-use lithium portable power products
(24370, 24379 and 24454) - Patent Pending. As well as,
most other lithium jump starters on the market.
INSTRUCTIONS
1. Turn off any accessories: light, radio, etc.
2. Make sure vehicle is off and remove key.
3. Connect the OBD2 Memory Saver to the vehicle’s
OBD2 port. Make sure the connector is fully
engaged.
4. Connect the OBD2 Memory Saver Plug to your
12V DC power supply’s EC5 connector. Make sure
the plug is firmly in place.
5. Disconnect the vehicles battery cables and
perform maintenance.
6. When maintenance is complete, connect vehicle
cables to the vehicle battery.
7. Immediately remove OBD2 Memory Saver from the
power source and then the OBD2 adapter from the
OBD2 vehicle port.
NOTE:
Never start the vehicle or turn on the accessories with
the OBD2 Memory Saver connected to the vehicle.
When working with a vehicle’s battery, review all of
the battery manufacturer’s and vehicle manufacturer’s
safety instructions, warnings and directions regarding
battery disconnection, removal and replacement.
The vehicle’s electrical system is receiving power from
the Memory Saver through the OBD2 port. Therefore,
the vehicle’s battery connectors are electrically live and
will still conduct electricity. They must be covered with
an insulator to prevent the connectors from touching
metal or each other and causing a short circuit.
Allowing a short circuit to occur could cause damage
to the electrical system of the vehicle.
NOTE:
Do not use an extension cable on either end of the
memory saver. Doing so could cause the vehicle’s
memory to be lost or cause the other vehicle damage.
TROUBLESHOOTING
The Memory Savor contains a 5 AMP fuse. Should
an issue occur with the Memory Saver, check the
fuse prior to calling customer service.
Do not operate the tool in explosive atmospheres,
such as in the presence of flammable liquids, gases
or dust
Do not expose the tool to heat
Do not store in locations where the temperature may
exceed 70°C
Do not modify or disassemble OEMTOOLS OBD2
Memory Saver. Only a repair technician may repair
this unit.
CAUTION
CAUTION
Always take care when using this tool
This power source is not intended for use by young
or infirm persons without supervision
Do not use as a toy
Do not allow the tool to become wet.
Do not immerse tool in water
