background image

 

 

 
 
 
 

 

 

19 

9. USING THE (SUPER) BLACK BOX 

 
 

9.1. Option: External Black Box 

 

 
 
 
 

Black-Box

Indicator LED

High-current plug

 

 
 
 
 
The LED lights up continuously when the power amplifier is on. The LED goes out when the protec-
tion circuitry trips. This is normal, as the protection circuitry cuts the power to the amplifier. 
 
 

Specifications: 
 

Dimensions: 

Width x height x depth = 170 x 97 x 257mm 

Weight: 3.1kg 
Connection cable: 

70cm long. Longer lengths available upon request 

 
 

Connecting to the amplifier 

 

  Warning!! Before connecting the Black Box, switch the unit off using the power 

switch and wait for 1 minute. 

 

When inserting the connector, guide the anti-rotation lug carefully into the mating 
recess in the socket.  

  When you switch the amplifier on, the LED on the front panel of the Black Box will 

illuminate. 

 

Please note

:  

 

When the amplifier's electronic protection circuitry cuts in, this will cause the LED 
on the Black Box to go out, as it interrupts the power to the amplifier.  

  Should you wish to disconnect the Black Box, switch the amplifier off first and wait 

until the LED on the Black Box goes out before doing so. 

 

Summary of Contents for V70
























Reviews: