background image

 

Document UT-MT-0693_EN 

Page 3 of 33 

 

Edition 15/01/2020 

Supersedes edition 08/01/2019 

 

LED INSET HELIPORT LIGHT LHI 
INSTRUCTION MANUAL FOR USE, INSTALLATION AND MAINTENANCE 

 

OPERATION ON THE EQUIPMENT - SKILLS 

Operation  on  the  equipment  and  access  to  its  internal  parts  shall  be  done  by  experienced  personnel, 
adequately trained and aware of the risks related to electricity and high voltages. 
Safety  rules  shall  be  adopted  when  operating  on  the  equipment,  or  on  cables  and  other  apparatus 
connected to the it 
 

DO NOT OPERATE ON ENERGIZED CIRCUITS 

Do not carry out any operation on the  converter or on apparatus connected to it when the circuits are 
energized. 
 

WHEN HANDLING AND SERVICING THIS EQUIPMENT, OBSERVE PRECAUTIONS FOR HIGH VOLTAGE 

EQUIPMENT. 

 

Before  any  access,  inspection  or  intervention,  be  sure  to  have  switched-off  the  unit,  opened  the  main 
circuit  breaker  and  removed  the  supply  to  the  unit  (by  opening  the  circuit  breaker/switch  on  the 
distribution board at the beginning of the supply line). 
 
Then  wait  discharge  time  (at  least  5  minutes),  ground  carefully  the  system,  and  check  for  voltage 
presence before accessing.. 
 

REANIMATION 

The  maintenance  staff  must  be  aware  of  the  risks  related  to  electricity,  criteria  to  prevent  the  risk  of 
electric shock and resuscitation techniques 
 

CE MARK 

 

 

This equipment  complies with the requirements of European regulations for the  CE mark.The 
user has to respect all prescriptions reported in this document. 
This  equipment  complies  with  the  requirements  of  the  EEC  directives  2004/108/EEC  and 

2006/95/EEC  with  regard  to  “Electromagnetic  Compatibility”  and  “Low  Voltage  Electrical 
Apparatus” respectively.

 

 

OUT OF SERVICE 

In  case  of  dismantling,  decommissioning,  destruction,  disposal,  the  user  shall  follow  all  the  required 
precautions for component and material elimination, according to local rules and applicable law. 

Summary of Contents for LHI


































Reviews: