background image

7

inside the hull, remove it with acetone before sanding.

4. 

Place light fixture into position or use mounting template provided. Mark the screw hole position 
and pilot drill using correct sized drill bit for included screws. 

5. 

Always dry fit units before applying any sealant. 

2.2 Installing the light fixture

TIP:

  Use a suitable marine sealant such as 3M™ Marine Adhesive Sealant Fast Cure 4200FS. When applying 

sealant to light fixture, be careful to protect the lens from any abrasive surface/floor so as not to 
remove the protective Tritonium coating.

1.  

Once hull preparation is complete, the light can be inserted into the hole previously prepared. Apply 
generous amounts of the sealant you are using to the back perimeter of the light body. Make sure 
to generously coat the cable of the light where it meets the back of the light. There should be an 
unbroken bead of sealant around the perimeter of the light unit, screw holes and cable exit. 

3.  

Position the light on to the hull, feeding the cable through first and seat into place. Press the light 
hard onto the hull to ensure good adhesion.

4. 

To ensure correct dispersion of light underwater, ensure all Sport Lights are mounted with the 
correct orientation with logo facing upwards. 

WARNING:

 

Tighten the screws with a hand tool ONLY!

  

Summary of Contents for Sport Series





















Reviews: