background image

Sauna & Steam

Oceanic Saunas  01902 450 550  sales

@oceanic-saunas.co.uk www.oceanic-saunas.co.uk

15

Sauna Heater Manual

heater element, the stones should plainly cover the heater element (refer to Pile stones fig8). The 

diameter of stone is about 3-8cm.

Rearrange the stones in the heater at least once a year or twice if it is in frequent use (maximum 

500 hrs). To decide the correct volume of stones in heater, refer to table 1 (Technical parameter ) 

provided.

8.9.  9. Insulation 

The door, ceiling and walls of sauna room must be insulated.  For every square meter of wall panel 

that is not insulated the size of cabin should decrease by 1.3 cubic meters in relation to the model 

of heater. Refer to table 1.

Ensure insulation is water proofed to prevent moisture spreading to the other rooms or wall 

structure .  Moisture-proofing must be placed between panel and heating insulation.

Moisture and thermal proofing should be installed from outside to inside, such as:

i.  Recommend that the MIN thickness of the thermal insulation in the walls in 50mm and in the 

ceiling 100mm.

ii.  Aluminum foil laminate is affixed over the heating insulation as a moisture-proof. 

iii.  Leave at least 20mm air slot between moisture-proof Aluminum foil and inside panel.

iv.  Leave a slot between wall panel and ceiling to prevent gathering vapor.

8.10.  10. 

Air ventilation of sauna room 

•  Mix the cold air with hot air to relieve mugginess when bathing.

•  Draw the fresh air around the heater to ventilate the sauna room.

•  Move the heater air to the farthest part of sauna room considering air ventilation of sauna 

room, the inlet and outlet vent should be installed. 

The inlet vent may be installed on the wall below the heater. (fig 15a).when using mechanical 

ventilation ,inlet vent is placed 50cm above the heater (fig 15b) or on the ceiling above the heater 

(fig 15c).the heavy cold air that blown into sauna room is mixed with the light not air from the 

heater ,bringing fresh air for bathers. The recommended inlet should have a diameter of 5—10cm.

The outlet vent should be placed diagonally opposite to the inlet. It is advised the outlet vent is 

placed under the platform in sauna room as far as possible from the inlet vent. It can be installed 

near the floor, or lead outside through a pipe from the floor going to a vent to the sauna ceiling, 

or under the door (to the wash room). In this case, the sill slot must be at least 5cm and it is 

recommended there is mechanical ventilation in washroom the size of the outlet should be twice 

of the inlet. 

 Warning: 

Summary of Contents for OCS B Series





















Reviews: