Ocean Sonics BP2-B1 User Manual Download Page 3

 

 

                                                       Battery Pack User Guide                         March 2020             P.2 

Introduction 

The Ocean Sonics Battery Pack

 

is a submersible unit that 

provides additional power to one or more hydrophones for long 
term deployments. The pack uses a maximum of 72 D-cell 
batteries that are field changeable and can provide power for 
one hydrophone for 30-90 days. All battery packs are made of 
lightweight glass fibre composite case. There are 3 types of end 
cap materials for varying depth ratings of 200m (Engineered 
Plastic), 900m (Anodized Aluminum) and 3500m (Titanium). 

Above weights are for a 200 m depth rated battery pack. Weights will differ slightly 
depending on depth rating, due to end cap material. 

 

 

 

 

 

 

Number of days the 

Battery Pack can  

power hydrophones:

 

Number of 

Channels 

Alkaline 

Lithium 

30 

90 

15 

42 

10 

26 

7.5 

19 

 

The 

B3

 model of Ocean Sonics Battery Packs 

can be easily configured for the use with 

alkaline

 or 

lithium

 batteries. Internally, each 

cell stack is individually protected against 

reverse bias; as well as the accidental 

population of cells at different charge states. 

Undervoltage and overvoltage detection 

circuitry is also present. This circuitry is 

integrated to assure the battery pack output 

voltages are always within specification.

 

 

Specification

 

Alkaline 

Lithium Primary 

Nominal Voltage (range) 

28 V (15 to 29) 

22 V (18 to 25) 

Battery Capacity 

1500 Wh 

4500 Wh 

Depth Rating (extended) 

200 m, 900 m, 3500 m 

900 m, 3500 m 

Weight Empty (in air) 

16 kg 

16 kg 

Weight Full (in air) 

26 kg appr. 

23 kg appr. 

Weight Full in Seawater 

9 kgf appr. 

7 kgf appr. 

Overall Length 

70 cm 

70 cm 

Outside Diameter 

18 cm  

18 cm  

Summary of Contents for BP2-B1












Reviews: