background image

About this guide .............................................................................................................................. 4 

Quick start guide ............................................................................................................................. 5 

2.1 

Opening and closing the housing ..................................................................................... 5 

2.2 

Batteries ........................................................................................................................... 5 

2.3 

Installing the hydrophone ................................................................................................ 6 

2.4 

Install the SoundTrap host on your PC ............................................................................. 6 

2.5 

Connect SoundTrap to your PC ........................................................................................ 7 

2.6 

Check SoundTrap Status .................................................................................................. 8 

2.7 

Configure the deployment ............................................................................................... 8 

2.8 

Begin recording using the IR Remote Control ................................................................ 10 

2.9 

Data Offload ................................................................................................................... 11 

More details .................................................................................................................................. 12 

3.1 

Adding additional memory cards ................................................................................... 12 

3.2 

Data Files ........................................................................................................................ 13 

3.3 

Calculation of deployment endurance ........................................................................... 14 

3.4 

Deployment hardware ................................................................................................... 15 

3.5 

Software updates ........................................................................................................... 16 

3.6 

MSP firmware updates ................................................................................................... 16 

3.7 

Calibration ...................................................................................................................... 16 

3.8 

Troubleshooting ............................................................................................................. 19 

Appendices .................................................................................................................................... 20 

4.1 

SoundTrap HF Click Detector (ST500HF Only)................................................................ 20 

Summary of Contents for SoundTrap ST500

























Reviews: