background image

Regulation notices

Introduction

This section describes the regulation notices.

Radio Interference suppression (all countries except USA)

Warning: This is a Class A product. In a domestic environment this product may cause
radio interference in which case the user may be required to take adequate measures.

FCC approval (USA only)

This system has been tested and found to comply with the limits for a class A digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the system is operated in a commercial en-
vironment. This system generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area
is likely to cause harmful interference in which case the user will be required to correct
the interference at his own expense.

ICES-003 Interference-causing equipment (Canada only)

This Class A digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

Harmonics (EU only)

Equipment complying with EN61000-3-12.

VCCI (Japan only)

Class A ITE

This is a Class A product based on the standard of the VCCI Council. If this equipment
is used in a domestic environment, radio interference may occur. In such cases, the user
may be required to take corrective action.

Ozone (all countries)

This machine is fitted with an ozone filter whose service life is equal to that of the machine
and therefore does not need replacing.

Chapter 2 - Regulation notices

12

Regulation notices

Summary of Contents for TDS750

























Reviews: