background image

OWNER’S MANUAL

308–209

Rev A

FULTRONIC 1000 Airless Paint Sprayer

1 GPM, Electric

Model 235–040, Series A

3000 psi (210 bar) MAXIMUM WORKING PRESSURE

TABLE OF CONTENTS

Warnings

2

. . . . . . . . . . . . . . . . . . . . . 

Setup

8

. . . . . . . . . . . . . . . . . . . . . . . . 

Startup

10

. . . . . . . . . . . . . . . . . . . . . . 

Maintenance

11

. . . . . . . . . . . . . . . . . 

Flushing Guidelines

12

. . . . . . . . . . . 

Application Techniques

13

. . . . . . . . 

Troubleshooting Guide

14

. . . . . . . . 

Repair

21

. . . . . . . . . . . . . . . . . . . . . . 

Parts

37

. . . . . . . . . . . . . . . . . . . . . . . 

Accessories

42

. . . . . . . . . . . . . . . . . 

Technical Data

43

. . . . . . . . . . . . . . . 

Dimensions

43

. . . . . . . . . . . . . . . . . . 

Warranty

44

. . . . . . . . . . . . . . . . . . . . 

THE O’BRIEN CORPORATION, 450 E. Grand Avenue, So. San Francisco, CA 94080

COPYRIGHT 1992, GRACO INC.

This manual contains

 IMPORTANT

INSTRUCTIONS and WARNINGS.

READ AND RETAIN FOR REFERENCE.

Liquids can be injected into the body by high pressure  airless  spray

or  leaks – especially hose leaks.

Keep body clear of the nozzle. Never stop leaks with any part of the

body.  Drain  all pressure before removing parts.A void accidental

triggering of gun by always setting safety latch when not spraying.

Never spray without a tip guard.

In case of accidental skin injection, seek immediate

“Surgical Treatment”.

Failure to follow this warning can result in amputation or serious

injury.

FIRE AND

EXPLOSION HAZARD

SKIN INJECTION

HAZARD

READ AND UNDERSTAND ALL LABELS AND INSTRUCTION MANUALS BEFORE USE

Spray painting, flushing or cleaning equipment with flammable liq-

uids in confined areas can result in fire or explosion.
Use  outdoors or in extremely well ventilated areas. Ground equip-

ment, hoses, containers and objects being sprayed.
Avoid all ignition sources such as static electricity from plastic

drop cloths, open flames such as pilot lights, hot objects such as

cigarettes,  arcs from connecting or disconnecting power cords or

turning light switches on and off.
Failure to follow this warning can result in death or serious injury.

NOTE:

This is an example of the DANGER label on your sprayer. 

This label is available in other languages, free of charge. 

See page 42 to order.

Summary of Contents for 235-040 A













































Reviews: