background image

-  EN  - 

36

 

 

 

3.1 

Hazards encountered by the combination of water and electricity 

 

The combination of water and electricity can lead to death or severe injury from electrocution, if the 
unit is incorrectly connected or misused. 

 

Prior to reaching into the water, always switch off the mains voltage to all units used in the water. 

 

 

 

3.2 

Danger for persons with pacemakers 

 

 

The container cover contains a magnet with a strong magnetic field that may affect the operation of 
pacemakers or implantable cardioverter defibrillators (ICDs). Always keep magnets at least 20 cm 
away from implanted devices. 

 

 

 

3.3 

Correct electrical installation 

 

 

Electrical installations must meet the national regulations and may only be carried out by a qualified 
electrician. 

 

A person is regarded as a qualified electrician, if, due to his/her vocational education, knowledge and 
experience, he or she is capable of and authorised to judge and carry out the work commissioned to 
him/her. This also includes the recognition of possible hazards and the adherence to the pertinent 
regional and national standards, rules and regulations. 

 

For your own safety, please consult a qualified electrician. 

 

The unit may only be connected when the electrical data of the unit and the power supply coincide. 
The unit data is to be found on the unit type plate or on the packaging, or in this manual. 

 

 

Ensure that the unit is fused for a rated fault current of max. 30 mA by means of a fault current 
protection device. 

 

 

Extension cables and power distributors (e. g. outlet strips) must be suitable for outdoor use. 

 

 

Protect the plug connections from moisture. 

 

 

Only plug the unit into a correctly fitted socket. 

 

 

 

3.4 Safe 

operation 

 

 

 

Never operate the unit if either the electrical cables or the housing are defective! 

 

Do not carry or pull the unit by its electrical cable.  

 

Route cords/hoses/lines in a way that they are protected against damage, and ensure that they do not 
present a tripping obstacle. 

 

Only open the unit housing or its attendant components, when this is explicitly required in the operating 
instructions. 

 

Only execute work on the unit that is described in this manual. If problems cannot be overcome, please 
contact an authorised customer service point or, when in doubt, the manufacturer. 

 

Only use original spare parts and accessories for the unit. 

 

Never carry out technical modifications to the unit. 

 

 

The power connection cables cannot be replaced. When the cable is damaged, the unit or the 
component needs to be disposed of. 

 

 

Keep the socket and power plug dry. 

 

 

Overvoltage in the mains could lead to operating malfunctions of the unit. For information, please refer 
to chapter "Remedy of faults". 

 

 

Do not breath in the spray from the rinsing device. The spray may contain harmful bacteria. When the 
container cover is lifted up, the rinsing device continues operating. 

 

Summary of Contents for BioTec Premium 80000







































Reviews: