background image

6

INSTALLATION

The Tables come completely assembled and ready to use. Plug the cord 

into a functioning outlet that is rated for the table.

Arrange the power cord and control cords so that they will not create a 

tripping hazard and where the controls are located to your liking and 

are conveniently accessible.

Be sure access to plug is not blocked for disconnecting the table from 

power.

This product must be grounded. If it should malfunction or break down, 

grounding provides a path of least resistance for electrical current to reduce 

the risk of electric shock. This product is equipped with a cord having an 

equipment-grounding conductor and a grounding plug. The plug must be 

plugged into an appropriate outlet that is properly installed and grounded in 

accordance with all local codes and ordinances. See U.S. sample below.

This product is manufactured for use on a nominal 120-volt circuit for the 

United States and a nominal 220-volt circuit for use in Europe. The plug has 

a grounding pin (see figure A) in a pattern that varies by country as shown 

in the Product Identification section of this manual. Make sure that the 

product is connected to an outlet having the same configuration as the plug.

Correct Implementation

Incorrect Implementation

DANGER-

Improper connection of the equipment-grounding conductor 

(see figure B) can result in a risk of electric shock. Check with a quali-

fied  electrician or service man if you are in doubt as to whether the product 

is properly grounded. Do not modify the plug provided with the product 

- if it will not fit the outlet, have a proper outlet installed by a qualified 

electrician.

To reduce the risk of electric shock, this furnishing has a polarized plug. 

This plug will fit in a polarized outlet only one way. Do not change the 

plug in any way.

 

Be sure to read all 

 

 

cautions, warnings    

 

and instructions given   

in the manual to  prevent 
injury to both operator  
and client.

GROUNDING

INSTALLATION

WARNING

Figure A

Figure B

DANGER

Summary of Contents for PG Series





























Reviews: